BenQ W1210ST User Manual - Page 20

Changing the password, Disabling the password function, Advanced, System Setup : Advanced, Password

Get BenQ W1210ST PDF manuals and user guides View all BenQ W1210ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

2. Write down the number and turn off the projector. 3. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. The "XXX" shown in the above messages are numbers that vary depending on different models. Changing the password To do this, first and foremost, you have to access the Advanced OSD menu (see page 25 for details). 1. Go to System Setup : Advanced > Password to display the Password window. 2. Select Change Password and press OK to display the Input Current Password window. Input Current Password Back 3. Use the arrow keys on the projector or remote control to enter the old password. • If the password is correct, the Input New Password window is displayed. • If the password is incorrect, the password error message is displayed, and the Input Current Password window appears for your retry. You can either try another password or press BACK to cancel the change. 4. Enter a new password. 5. Re-enter the same password to verify. Do make a note of your password, and then keep the note in a safe place for later recall. 6. You have successfully set a new password. Remember to enter the new password next time you turn on the projector. 7. Press BACK to save your changes and exit. Disabling the password function To do this, first and foremost, you have to access the Advanced OSD menu (see page 25 for details). 1. Go to System Setup : Advanced > Password to display the Password window. 2. Select Power On Lock and use / to set Off. 3. Enter the current password. • If the password is correct, the Password window displays that Power On Lock is Off. You will not be asked to enter the password next time you turn on the projector. • If the password is incorrect, the password error message is displayed, and then the Input Password window is displayed for your retry. You can either try another password or press BACK to cancel the change. 4. Press BACK to save your changes and exit. Though the password function is disabled, you need to keep a note of the old password in case you ever need to re-activate the password function by entering the old password. 20 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
20
Operation
2.
Write down the number and turn off the projector.
3.
Seek help from the local BenQ service center to decode the number. You may be required to provide
proof of purchase documentation to verify that you are an authorized user of the projector.
The "XXX" shown in the above messages are numbers that vary depending on different models.
Changing the password
To do this, first and foremost, you have to access the
Advanced
OSD menu (see page
25
for details).
1.
Go to
System Setup : Advanced
>
Password
to display the
Password
window.
2.
Select
Change Password
and press
OK
to display the
Input Current Password
window.
3.
Use the arrow keys on the projector or remote control to enter the old password.
•
If the password is correct, the
Input New Password
window is displayed.
•
If the password is incorrect, the password error message is displayed, and the
Input Current
Password
window appears for your retry. You can either try another password or press
BACK
to cancel the change.
4.
Enter a new password.
5.
Re-enter the same password to verify.
Do make a note of your password, and then keep the note in a safe place for later recall.
6.
You have successfully set a new password. Remember to enter the new password next time you turn
on the projector.
7.
Press
BACK
to save your changes and exit.
Disabling the password function
To do this, first and foremost, you have to access the
Advanced
OSD menu (see page
25
for details).
1.
Go to
System Setup : Advanced
>
Password
to display the
Password
window.
2.
Select
Power On Lock
and use
/
to set
Off
.
3.
Enter the current password.
•
If the password is correct, the
Password
window displays that
Power On Lock
is
Off
. You will
not be asked to enter the password next time you turn on the projector.
•
If the password is incorrect, the password error message is displayed, and then the
Input
Password
window is displayed for your retry. You can either try another password or press
BACK
to cancel the change.
4.
Press
BACK
to save your changes and exit.
Though the password function is disabled, you need to keep a note of the old password in case you ever need
to re-activate the password function by entering the old password.
Input Current Password
Back