Adaptec 2420SA User Guide - Page 27

Selecting Disk Drives, Disk Drives for SAS Controllers - storage manager

Get Adaptec 2420SA - Serial ATA II RAID Controller PDF manuals and user guides
UPC - 760884149331
View all Adaptec 2420SA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Chapter 4: Getting Started ● 27 Selecting Disk Drives When selecting disk drives for your RAID array, ensure that all the disk drives have the same performance level. You can use different-sized disk drives in the array, but the array will be limited to the capacity of the smallest and slowest disk drive. For more information, refer to the Adaptec Storage Manager User's Guide for Internal RAID Storage or online Help. Disk Drives for SAS Controllers Your SAS controller supports both SAS and SATA disk drives. For cable information, see page 28. Disk Drives for SATA Controllers Your SATA controller supports SATA disk drives only. You need one SATA port for each disk drive you are connecting to your SATA controller. Disk Drives for SCSI Controllers Your SCSI controller supports Ultra320 SCSI disk drives. It also supports Ultra2 or higher SCSI disk drives and peripherals, but at performance levels less than Ultra320. Adaptec does not recommend using SCSI disk drives or peripherals older than Ultra2. Note: High-voltage Differential (HVD) disk drives are not supported and will damage your controller. If you are mixing single-ended (SE) disk drives with Low-voltage Differential (LVD) disk drives: ● Ensure proper termination by using a cable (like the one included in the kit) with a built- in multimode terminator and proper adapters. ● Disable termination on all the SE disk drives. ● Put LVD and SE disk drives on separate channels for the best performance. Note: If you mix SE and Ultra320 disk drives on the same channel, the performance of the Ultra320 disk drives is reduced to SE levels.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Chapter 4: Getting Started
●
27
Selecting Disk Drives
When selecting disk drives for your RAID array, ensure that all the disk drives have the same
performance level. You can use different-sized disk drives in the array, but the array will be
limited to the capacity of the smallest and slowest disk drive.
For more information, refer to the
Adaptec Storage Manager User’s Guide
f
or Internal RAID
Storage
or online Help.
Disk Drives for SAS Controllers
Your SAS controller supports both SAS and SATA disk drives. For cable information, see
page 28
.
Disk Drives for SATA Controllers
Your SATA controller supports SATA disk drives only. You need one SATA port for each disk
drive you are connecting to your SATA controller.
Disk Drives for SCSI Controllers
Your SCSI controller supports Ultra320 SCSI disk drives. It also supports Ultra2 or higher
SCSI disk drives and peripherals, but at performance levels less than Ultra320. Adaptec does
not recommend using SCSI disk drives or peripherals older than Ultra2.
Note:
High-voltage Differential (HVD) disk drives are not supported and will damage your
controller.
If you are mixing single-ended (SE) disk drives with Low-voltage Differential (LVD) disk
drives:
●
Ensure proper termination by using a cable (like the one included in the kit) with a built-
in multimode terminator and proper adapters.
●
Disable termination on all the SE disk drives.
●
Put LVD and SE disk drives on separate channels for the best performance.
Note:
If you mix SE and Ultra320 disk drives on the same channel, the performance of the
Ultra320 disk drives is reduced to SE levels.