Actiontec V1000H User Manual - Page 24

Upper, Lower, Apply, Set the MSDU MAC-Layer Service Data Unit aggregation state by clicking

Get Actiontec V1000H PDF manuals and user guides View all Actiontec V1000H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Chapter 3 Wireless Settings To change the radio settings of the Modem Router's wireless network (if needed; you do not need to make all the changes in this procedure, as they can be changed independently of each other): 1. Select the radio's channel from the Channel drop-down list. 2. Select the level of the wireless radio's power level. 3. Select the wireless network's mode. Options include whatever mix of 802.11b, g, and n modes you prefer (except b/n only). 4. Select the channel width by clicking in either the 20 Mhz or 40 Mhz radio buttons. 5. If 40 Mhz was selected in step 5, select the channel's width (Upper or Lower). 6. Set the MSDU (MAC-Layer Service Data Unit) aggregation state by clicking in the Enable or Disable radio buttons below step 6. MDSU should only be enabled/disabled by an experienced network technician. 7. Set the MPDU (MAC-Layer Protocol Data Unit) aggregation state by clicking in the Enable or Disable radio buttons below step 7. MPDU should only be enabled/disabled by an experienced network technician. 8. Click Apply. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
21
Chapter 3
Wireless Settings
To change the radio settings of the Modem Router’s wireless network (if needed;
you do not need to make all the changes in this procedure, as they can be changed
independently of each other):
Select the radio’s channel from the Channel drop-down list.
1.
Select the level of the wireless radio’s power level.
2.
Select the wireless network’s mode. Options include whatever mix of 802.11b,
3.
g, and n modes you prefer (except b/n only).
Select the channel width by clicking in either the 20 Mhz or 40 Mhz
4.
radio buttons.
If 40 Mhz was selected in step 5, select the channel’s width (
5.
Upper
or
Lower
).
Set the MSDU (MAC-Layer Service Data Unit) aggregation state by clicking
6.
in the Enable or Disable radio buttons below step 6. MDSU should only be
enabled/disabled by an experienced network technician.
Set the MPDU (MAC-Layer Protocol Data Unit) aggregation state by clicking
7.
in the Enable or Disable radio buttons below step 7. MPDU should only be
enabled/disabled by an experienced network technician.
Click
8.
Apply
.