2012 Yamaha Motorsports Raider SCL Owners Manual - Page 74

2012 Yamaha Motorsports Raider SCL Manual

Get 2012 Yamaha Motorsports Raider SCL PDF manuals and user guides View all 2012 Yamaha Motorsports Raider SCL manuals

Page 74 highlights

PERIODIC MAINTENANCE AND ADJUSTMENT EAU24324 1 Replacing a license plate light bulb 1. Remove the license plate light unit by removing the nuts, washers and rubber dampers. 1. Turn signal light bulb 7 3. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops. 4. Install the lens by installing the screws. NOTICE: Do not overtighten the screws, otherwise the lens may break. [ECA10681] 1. 2. 3. 4. Nut Washer License plate light bulb License plate light lens 1. 2. 3. 4. Nut Washer Rubber damper License plate light unit 2. Remove the license plate light lens by removing the nuts and washers. 3. Remove the burnt-out bulb by pulling it out. 4. Insert a new bulb into the socket. 5. Install the license plate light lens by installing the washers and the nuts. 6. Install the license plate light unit by installing the rubber dampers, washers and the nuts. 7-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
PERIODIC MAINTENANCE AND ADJUSTMENT
7-31
7
3.
Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
NOTICE:
Do not over-
tighten the screws, otherwise
the lens may break.
[ECA10681]
EAU24324
Replacing a license plate light
bulb
1.
Remove the license plate light unit
by removing the nuts, washers and
rubber dampers.
2.
Remove the license plate light lens
by removing the nuts and washers.
3.
Remove the burnt-out bulb by pull-
ing it out.
4.
Insert a new bulb into the socket.
5. Install the license plate light lens
by installing the washers and the
nuts.
6.
Install the license plate light unit by
installing the rubber dampers,
washers and the nuts.
1.
Turn signal light bulb
1
1. Nut
2. Washer
3.
Rubber damper
4.
License plate light unit
1. Nut
2. Washer
3.
License plate light bulb
4.
License plate light lens