2012 Yamaha Motorsports Grizzly 125 Automatic Owners Manual - Page 102

2012 Yamaha Motorsports Grizzly 125 Automatic Manual

Get 2012 Yamaha Motorsports Grizzly 125 Automatic PDF manuals and user guides View all 2012 Yamaha Motorsports Grizzly 125 Automatic manuals

Page 102 highlights

Tightening torques: Drive chain slack adjusting bolt locknut: 16 Nm (1.6 m·kgf, 12 ft·lbf) Axle holding bolt (upper): 85 Nm (8.5 m·kgf, 61 ft·lbf) Axle holding bolt (lower): 60 Nm (6.0 m·kgf, 43 ft·lbf) ECB00551 6. Tighten the hub stopper bolt and hub stopper bolt locknut to the specified torques. Tightening torques: Hub stopper bolt: 16 Nm (1.6 m·kgf, 12 ft·lbf) Hub stopper bolt locknut: 16 Nm (1.6 m·kgf, 12 ft·lbf) EBU24882 NOTICE If measurement "A" of the drive chain slack adjusting bolt is less than 27 mm (1.06 in), have a Yamaha dealer replace the drive chain. Lubricating the drive chain The drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrication chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas. Service the drive chain as follows. ECB00561 8 NOTICE The drive chain must be lubricated after washing the ATV or riding in the rain or wet areas. 1 1. Measurement A 8-36 1. Clean the drive chain with kerosene and a small soft brush. NOTICE: To prevent damaging the O-rings, do not clean the drive chain with steam cleaners, high-pressure washers or inappropriate solvents. [ECB00571]

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
8-36
8
NOTICE
ECB00551
If measurement “A” of the drive chain slack ad-
justing bolt is less than 27 mm (1.06 in), have a
Yamaha dealer replace the drive chain.
6.
Tighten the hub stopper bolt and hub stopper
bolt locknut to the specified torques.
EBU24882
Lubricating the drive chain
The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.
NOTICE
ECB00561
The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.
1. Clean the drive chain with kerosene and a
small soft brush.
NOTICE:
To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
Tightening torques:
Drive chain slack adjusting bolt locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle holding bolt (upper):
85 Nm (8.5 m·kgf, 61 ft·lbf)
Axle holding bolt (lower):
60 Nm (6.0 m·kgf, 43 ft·lbf)
1.
Measurement A
1
Tightening torques:
Hub stopper bolt:
16 Nm (1.6 m·kgf, 12 ft·lbf)
Hub stopper bolt locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)