2011 Yamaha Motorsports V Star 650 Custom Owners Manual - Page 74

2011 Yamaha Motorsports V Star 650 Custom Manual

Get 2011 Yamaha Motorsports V Star 650 Custom PDF manuals and user guides View all 2011 Yamaha Motorsports V Star 650 Custom manuals

Page 74 highlights

PERIODIC MAINTENANCE AND ADJUSTMENT 1 1. Bolt 2. Final gear case 1. Drive shaft 1. Middle gear universal joint 2. Drive shaft 7 7. Lift the rear wheel off the ground according to the procedure on page 7-33. 8. While supporting the drive shaft, pull the rear wheel back to remove the following parts as an assembly: wheel, wheel axle, final gear case, and drive shaft. TIP Make sure to support the drive shaft as it is being pulled out. EAU25512 To install the rear wheel 1. Install the rear wheel, wheel axle, final gear case, and drive shaft by pushing the wheel forward and guiding the drive shaft into the middle gear universal joint. 2. Install the final gear case bolts. 3. Install the brake rod onto the brake camshaft lever, and then install the brake pedal free play adjusting nut onto the brake rod. 4. Install the brake torque rod bolt and nut at the brake shoe plate. 5. Install the panel. 6. Lower the rear wheel so that it is on the ground, and then put the sidestand down. 7. Tighten the axle nut, the final gear case bolts and the brake torque rod nuts to the specified torques. 7-36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
PERIODIC MAINTENANCE AND ADJUSTMENT
7-36
7
7. Lift the rear wheel off the ground
according to the procedure on
page 7-33.
8. While supporting the drive shaft,
pull the rear wheel back to remove
the following parts as an assem-
bly: wheel, wheel axle, final gear
case, and drive shaft.
TIP
Make sure to support the drive shaft as
it is being pulled out.
EAU25512
To install the rear wheel
1.
Install the rear wheel, wheel axle,
final gear case, and drive shaft by
pushing the wheel forward and
guiding the drive shaft into the mid-
dle gear universal joint.
2.
Install the final gear case bolts.
3.
Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.
4. Install the brake torque rod bolt
and nut at the brake shoe plate.
5.
Install the panel.
6.
Lower the rear wheel so that it is
on the ground, and then put the
sidestand down.
7.
Tighten the axle nut, the final gear
case bolts and the brake torque
rod nuts to the specified torques.
1. Bolt
2.
Final gear case
1.
Drive shaft
1
1.
Middle gear universal joint
2.
Drive shaft