2010 Yamaha Motorsports RS Venture Owners Manual - Page 85

2010 Yamaha Motorsports RS Venture Manual

Get 2010 Yamaha Motorsports RS Venture PDF manuals and user guides View all 2010 Yamaha Motorsports RS Venture manuals

Page 85 highlights

Troubleshooting 7. Pull the black (-) connecting lead cover to expose the terminal through the slit in the cover, and then connect the black (-) jumper cable to the black (-) connecting lead. G G G Faulty wire connections: Check connections or ask a Yamaha dealer to inspect. Discharged battery: Charge battery or see "Discharged battery" above. Seized engine: Seizure is caused by poor lubrication, inadequate fuel, or an air leak. Ask a Yamaha dealer to inspect. Low coolant temperature indicator light is flashing: Warm the engine up. Faulty spark plugs: Clean or replace the spark plugs. Improper fuel flow: See "Engine turns over but does not start-Fuel system" above. Incorrect V-belt clutch settings for altitude or conditions: Ask a Yamaha dealer to inspect. Engine power is low G G G G 8. 9. 10. 11. 12. 13. 14. Start the engine. Disconnect the black (-) jumper cable from the black (-) connecting lead, and then pull the cover completely over the lead terminal. Disconnect the black (-) jumper cable from the negative (-) terminal of the battery used to jump start the engine. Disconnect the red (+) jumper cable from the positive (+) terminal of the battery used to jump start the engine. Disconnect the red (+) jumper cable from the red (+) connecting lead, and then pull the cover completely over the lead terminal. Install the red (+) connecting lead into the lead holder. Install the right side cover and the shroud. Engine constantly backfires or misfires G G G Faulty spark plugs: Replace the spark plugs. Clogged fuel system: See "Engine turns over but does not start-Fuel system" above. Malfunctioning T.O.R.S.: See "Engine turns over but does not start-Electrical system" above. Insufficient coolant: Add coolant. Air in cooling system: Bleed the cooling system or ask a Yamaha dealer to inspect. Leaking coolant: Ask a Yamaha dealer to inspect. Malfunctioning V-belt clutch: Ask a Yamaha dealer to inspect. Drive track does not move: Foreign object is caught in the drive track, or slide runners have melted to the slide metal due to lack of lubrication. Tight, loose, or broken drive chain: Ask a Yamaha dealer to inspect. Engine overheats G G G TIP Make sure that both the red (+) connecting lead and the black (-) connecting lead are seated securely in the lead holders. Snowmobile does not move G G Electric starter does not operate or operates slowly G Engine stop switch is pushed in: Pull it out. G 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Troubleshooting
79
7.
Pull the black (–) connecting lead cover
to expose the terminal through the slit in
the cover, and then connect the black (–)
jumper cable to the black (–) connecting
lead.
8.
Start the engine.
9.
Disconnect the black (–) jumper cable
from the black (–) connecting lead, and
then pull the cover completely over the
lead terminal.
10. Disconnect the black (–) jumper cable
from the negative (–) terminal of the bat-
tery used to jump start the engine.
11.
Disconnect the red (+) jumper cable from
the positive (+) terminal of the battery
used to jump start the engine.
12.
Disconnect the red (+) jumper cable from
the red (+) connecting lead, and then pull
the cover completely over the lead termi-
nal.
13.
Install the red (+) connecting lead into the
lead holder.
14.
Install the right side cover and the shroud.
TIP
Make sure that both the red (+) connecting
lead and the black (–) connecting lead are
seated securely in the lead holders.
Electric starter does not operate or
operates slowly
●
Engine stop switch is pushed in: Pull it out.
●
Faulty wire connections: Check connec-
tions or ask a Yamaha dealer to inspect.
●
Discharged battery: Charge battery or see
“Discharged battery” above.
●
Seized engine: Seizure is caused by poor
lubrication, inadequate fuel, or an air leak.
Ask a Yamaha dealer to inspect.
Engine power is low
●
Low coolant temperature indicator light is
flashing: Warm the engine up.
●
Faulty spark plugs: Clean or replace the
spark plugs.
●
Improper fuel flow: See “Engine turns over
but does not start–Fuel system” above.
●
Incorrect V-belt clutch settings for altitude
or conditions: Ask a Yamaha dealer to in-
spect.
Engine constantly backfires or mis-
fires
●
Faulty spark plugs: Replace the spark
plugs.
●
Clogged fuel system: See “Engine turns
over but does not start–Fuel system”
above.
●
Malfunctioning T.O.R.S.: See “Engine turns
over but does not start–Electrical system”
above.
Engine overheats
●
Insufficient coolant: Add coolant.
●
Air in cooling system: Bleed the cooling sys-
tem or ask a Yamaha dealer to inspect.
●
Leaking coolant: Ask a Yamaha dealer to
inspect.
Snowmobile does not move
●
Malfunctioning V-belt clutch: Ask a Yamaha
dealer to inspect.
●
Drive track does not move: Foreign object is
caught in the drive track, or slide runners
have melted to the slide metal due to lack of
lubrication.
●
Tight, loose, or broken drive chain: Ask a
Yamaha dealer to inspect.