2010 Yamaha Motorsports RS Venture Owners Manual - Page 67

2010 Yamaha Motorsports RS Venture Manual

Get 2010 Yamaha Motorsports RS Venture PDF manuals and user guides View all 2010 Yamaha Motorsports RS Venture manuals

Page 67 highlights

Periodic maintenance and adjustment Standard V-belt position: From 1.5 mm (0.06 in) above the edge of the secondary sheave assembly to 0.5 mm (0.02 in) below the edge 8. If the V-belt position is incorrect, adjust it by removing or adding a spacer on each V-belt position adjusting bolt. 9. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lbf) 10. Install the V-belt over the primary sheave assembly. 11. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 1. Secondary sliding sheave 2. Secondary fixed sheave 12. Install the V-belt between the secondary sliding and fixed sheaves. 1. V-belt position adjusting bolt 2. Spacer V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer 1. V-belt Not necessary (It is correct.) 13. Place the left lower cover in the original position, and then install the bolts and screws. Add spacer 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Periodic maintenance and adjustment
61
8.
If the V-belt position is incorrect, adjust it
by removing or adding a spacer on each
V-belt position adjusting bolt.
9.
Tighten the V-belt position adjusting
bolts.
10.
Install the V-belt over the primary sheave
assembly.
11. Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
12.
Install the V-belt between the secondary
sliding and fixed sheaves.
13.
Place the left lower cover in the original
position, and then install the bolts and
screws.
Standard V-belt position:
From 1.5 mm (0.06 in) above the edge
of the secondary sheave assembly to
0.5 mm (0.02 in) below the edge
1.
V-belt position adjusting bolt
2. Spacer
V-belt position
Adjustment
More than 1.5 mm
(0.06 in) above the
edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
Not necessary (It is
correct.)
More than 0.5 mm
(0.02 in) below the
edge
Add spacer
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt