2009 Yamaha Motorsports Phazer R-TX Owners Manual - Page 69

2009 Yamaha Motorsports Phazer R-TX Manual

Get 2009 Yamaha Motorsports Phazer R-TX PDF manuals and user guides View all 2009 Yamaha Motorsports Phazer R-TX manuals

Page 69 highlights

Periodic maintenance and adjustment 6. 7. Install the new V-belt over the primary sheave assembly. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 2. 3. Remove the right side cover. (See page 49 for removal procedures.) Remove the dipstick, wipe it off with a clean rag, and then insert it back into the filler hole. 1. Secondary sliding sheave 2. Secondary fixed sheave 1. Dipstick 4. 8. Install the V-belt between the secondary fixed sheave and the secondary sliding sheave. Remove the dipstick and check that the oil level is within the range shown at the bottom of the dipstick. If the oil does not reach the bottom of the dipstick, add sufficient oil of the recommended type to raise it to the correct level. NOTICE: Make sure that no foreign material enters the drive chain housing. [ECS00531] 1. V-belt 9. Install the drive guard. 10. Install the left side cover (PZ50 / PZ50RT / PZ50GT / PZ50MT), or install the left side cover and the left upper cover, and then close the shroud (PZ50VT). ESU12124 1. Oil level range Drive chain housing To check the drive chain housing oil level 1. Place the snowmobile on a level surface and apply the parking brake. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
63
6.
Install the new V-belt over the primary
sheave assembly.
7.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
8.
Install the V-belt between the secondary
fixed sheave and the secondary sliding
sheave.
9.
Install the drive guard.
10. Install
the
left
side
cover
(PZ50 /
PZ50RT / PZ50GT / PZ50MT), or install
the left side cover and the left upper cov-
er, and then close the shroud (PZ50VT).
ESU12124
Drive chain housing
To check the drive chain housing oil level
1.
Place the snowmobile on a level surface
and apply the parking brake.
2.
Remove the right side cover. (See page
49 for removal procedures.)
3.
Remove the dipstick, wipe it off with a
clean rag, and then insert it back into the
filler hole.
4.
Remove the dipstick and check that the
oil level is within the range shown at the
bottom of the dipstick. If the oil does not
reach the bottom of the dipstick, add suf-
ficient oil of the recommended type to
raise it to the correct level.
NOTICE:
Make sure that no foreign material en-
ters the drive chain housing.
[ECS00531]
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt
1. Dipstick
1.
Oil level range