2009 Yamaha Motorsports Phazer R-TX Owners Manual - Page 63

2009 Yamaha Motorsports Phazer R-TX Manual

Get 2009 Yamaha Motorsports Phazer R-TX PDF manuals and user guides View all 2009 Yamaha Motorsports Phazer R-TX manuals

Page 63 highlights

Periodic maintenance and adjustment 5. Remove the oil filler cap, wipe the dipstick clean, insert it back into the oil filler hole (without screwing it in), and then remove it again to check the oil level. 2. Start the engine, warm it up for 10-15 minutes, and then turn it off. The engine can also be warmed up by driving the snowmobile for 10-15 minutes. After driving the snowmobile, allow the engine to idle for at least 10 seconds before turning it off. Remove the right side cover (PZ50 / PZ50RT / PZ50GT / PZ50MT), or open the shroud and remove the right upper cover and the right side cover (PZ50VT). (See page 49 for removal procedures.) Disconnect the oil level gauge coupler. NOTICE: Disconnect the oil level gauge coupler before removing the oil filler cap, otherwise the cable could twist and break. [ECS00452] 1. "H" level mark 2. "L" level mark TIP G 1. Oil filler cap 2. Dipstick G TIP The engine oil should be between the "H" and "L" level marks on the dipstick. 3. 4. 6. 1. Oil level gauge coupler 2. Oil filler cap If the engine oil is below the "L" level mark, add sufficient oil of the recommended type to raise it to the "H" level mark. (See page 81 for the recommended oil.) NOTICE: When adding the engine oil, be careful not to fill above the "H" level mark on the dipstick. Use only the recommended oil. (See page 81.) Make sure that no foreign material enters the engine oil tank. [ECS00462] 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
57
2.
Start the engine, warm it up for 10–15
minutes, and then turn it off.
TIP
●
The engine can also be warmed up by driv-
ing the snowmobile for 10–15 minutes.
●
After driving the snowmobile, allow the en-
gine to idle for at least 10 seconds before
turning it off.
3.
Remove the right side cover (PZ50 /
PZ50RT / PZ50GT / PZ50MT), or open
the shroud and remove the right upper
cover and the right side cover (PZ50VT).
(See page 49 for removal procedures.)
4.
Disconnect the oil level gauge coupler.
NOTICE:
Disconnect the oil level
gauge coupler before removing the oil
filler cap, otherwise the cable could
twist and break.
[ECS00452]
5.
Remove the oil filler cap, wipe the dipstick
clean, insert it back into the oil filler hole
(without screwing it in), and then remove
it again to check the oil level.
TIP
The engine oil should be between the “H” and
“L” level marks on the dipstick.
6.
If the engine oil is below the “L” level
mark, add sufficient oil of the recom-
mended type to raise it to the “H” level
mark. (See page 81 for the recommend-
ed oil.)
NOTICE:
When adding the en-
gine oil, be careful not to fill above the
“H” level mark on the dipstick. Use
only the recommended oil. (See page
81.) Make sure that no foreign material
enters the engine oil tank.
[ECS00462]
1.
Oil level gauge coupler
2.
Oil filler cap
1.
Oil filler cap
2. Dipstick
1.
“H” level mark
2.
“L” level mark