2008 Yamaha Motorsports RS Venture GT Owners Manual - Page 59

2008 Yamaha Motorsports RS Venture GT Manual

Get 2008 Yamaha Motorsports RS Venture GT PDF manuals and user guides View all 2008 Yamaha Motorsports RS Venture GT manuals

Page 59 highlights

Periodic maintenance force the V-belt between the sheaves; the secondary sliding and fixed sheaves must touch each other. 1. V-belt position adjusting bolt 2. Spacer 1. Edge of the secondary sheave assembly 2. V-belt position V-belt position More than 1.5 mm (0.06 in) above the edge From 1.5 mm (0.06 in) above the edge to 0.5 mm (0.02 in) below the edge More than 0.5 mm (0.02 in) below the edge Adjustment Remove spacer Standard V-belt position: From 1.5 mm (0.06 in) above the edge of the secondary sheave assembly to 0.5 mm (0.02 in) below the edge. 6. If the V-belt position is incorrect, adjust it by removing or adding a spacer on each V-belt position adjusting bolt. Not necessary (It is correct.) Add spacer 7. Tighten the V-belt position adjusting bolts. V-belt position adjusting bolt tightening torque: 10 Nm (1.0 m·kgf, 7.2 ft·lb) 8. Install the V-belt over the primary sheave assembly. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Periodic maintenance
53
force the V-belt between the sheaves; the
secondary sliding and fixed sheaves
must touch each other.
6.
If the V-belt position is incorrect, adjust it
by removing or adding a spacer on each
V-belt position adjusting bolt.
7.
Tighten the V-belt position adjusting
bolts.
8.
Install the V-belt over the primary sheave
assembly.
1.
Edge of the secondary sheave assembly
2.
V-belt position
Standard V-belt position:
From 1.5 mm (0.06 in) above the edge
of the secondary sheave assembly to
0.5 mm (0.02 in) below the edge.
1.
V-belt position adjusting bolt
2. Spacer
V-belt position
Adjustment
More than 1.5 mm
(0.06 in) above the
edge
Remove spacer
From 1.5 mm (0.06 in)
above the edge to 0.5
mm (0.02 in) below
the edge
Not necessary (It is
correct.)
More than 0.5 mm
(0.02 in) below the
edge
Add spacer
V-belt position adjusting bolt tightening
torque:
10 Nm (1.0 m·kgf, 7.2 ft·lb)