2002 Yamaha Motorsports V Star Custom Owners Manual - Page 91

2002 Yamaha Motorsports V Star Custom Manual

Get 2002 Yamaha Motorsports V Star Custom PDF manuals and user guides View all 2002 Yamaha Motorsports V Star Custom manuals

Page 91 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR 3. Install the brake rod onto the brake camshaft lever, and then install the brake pedal free play adjusting nut onto the brake rod. 4. Install the brake torque rod bolt at the brake shoe plate, and then tighten both bolts to the specified torque. 1. Bolt (× 4) 2. Final gear case 1. Middle gear universal joint 2. Drive shaft EAU04191 6 6. Remove the bolts that secure the final gear case to the swingarm. 7. Lift the rear wheel off the ground according to the procedure on page 6-36. 8. While supporting the drive shaft, pull the rear wheel back to remove the following parts as an assembly: wheel, wheel axle, final gear case, and drive shaft. NOTE: Make sure to support the drive shaft as it is being pulled out. @ @ To install the rear wheel 1. Install the rear wheel, wheel axle, final gear case, and drive shaft by pushing the wheel forward and guiding the drive shaft into the middle gear universal joint. 2. Install the final gear case bolts, and then tighten them to the specified torque. Tightening torque: Final gear case bolt: 74 Nm (7.4 m·kgf, 54 ft·lb) Tightening torque: Brake torque rod bolt: 20 Nm (2.0 m·kgf, 14 ft·lb) 5. Install the panel. 6. Lower the rear wheel so that it is on the ground. 7. Tighten the axle nut to the specified torque. Tightening torque: Axle nut: 92 Nm (9.2 m·kgf, 67 ft·lb) 8. Adjust the brake pedal free play. (See page 6-23 for brake pedal free play adjustment procedures.) 6-39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
PERIODIC MAINTENANCE AND MINOR REPAIR
6-39
6
6.
Remove the bolts that secure the
final gear case to the swingarm.
7.
Lift the rear wheel off the ground
according to the procedure on
page 6-36.
8. While supporting the drive shaft,
pull the rear wheel back to remove
the following parts as an assem-
bly: wheel, wheel axle, final gear
case, and drive shaft.
NOTE:
@
Make sure to support the drive shaft as
it is being pulled out.
@
EAU04191
To install the rear wheel
1.
Install the rear wheel, wheel axle,
final gear case, and drive shaft by
pushing the wheel forward and
guiding the drive shaft into the
middle gear universal joint.
2. Install the final gear case bolts,
and then tighten them to the spec-
ified torque.
3.
Install the brake rod onto the brake
camshaft lever, and then install
the brake pedal free play adjusting
nut onto the brake rod.
4.
Install the brake torque rod bolt at
the brake shoe plate, and then
tighten both bolts to the specified
torque.
5.
Install the panel.
6.
Lower the rear wheel so that it is
on the ground.
7.
Tighten the axle nut to the speci-
fied torque.
8. Adjust the brake pedal free play.
(See page 6-23 for brake pedal
free play adjustment procedures.)
1.
Bolt (
×
4)
2.
Final gear case
1.
Middle gear universal joint
2.
Drive shaft
Tightening torque:
Final gear case bolt:
74 Nm (7.4 m·kgf, 54 ft·lb)
Tightening torque:
Brake torque rod bolt:
20 Nm (2.0 m·kgf, 14 ft·lb)
Tightening torque:
Axle nut:
92 Nm (9.2 m·kgf, 67 ft·lb)