Sharp XG-P560W XG-P560W Operation Manual - Page 38

Switching the Input, Adjusting the Volume

Get Sharp XG-P560W - WXGA DLP Projector PDF manuals and user guides View all Sharp XG-P560W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Image Projection Switching the Input Mode Select the appropriate input mode for the connected equipment. Press COMPUTER1/2, DVI, HDMI, VIDEO or S-VIDEO on the remote control to select the input mode. ■ When you select the input mode with INPUT P/R on the projector or P/R on the remote control: • When P/R is pressed, the Input list appears. While the Input list is displayed, follow the procedure below to switch the input mode. - Press P/R to select the desired input mode and then press ENTER. • When "AUTO SEARCH" is selected, input signal is automatically detected. • If ENTER is not pressed, the projector switches to the selected input mode in a few seconds. Note • When no signal is received, "NO SIGNAL" will be displayed. When non-supported signal is received, "NOT REG." is displayed. • The input mode is not displayed when "OSD Display" of the "Options1" menu is set to "Level A" or "Level B". (See page 57.) Adjusting the Volume Press VOL +/- on the projector or on the remote control to adjust the volume. Note • Pressing VOL- will lower the volume. Pressing VOL+ will raise the volume. • When "Pict in Pict" (see page 56) is set to "On", audio volume cannot be adjusted on the projector. The audio volume buttons will instead function as location shift button for the smaller screen. -36 '/" buttons COMPUTER1/2, DVI, HDMI, VIDEO and S-VIDEO buttons Input mode menu "On-screen display Volume buttons

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
-36
Switching the Input
Mode
Select the appropriate input mode for the con-
nected equipment.
Press
COMPUTER1/2
,
DVI
,
HDMI
,
VIDEO
or
S-VIDEO
on the remote
control to select the input mode.
■
When you select the input mode with
INPUT
P
/
R
on the projector or
P
/
R
on
the remote control:
•
When
P
/
R
is pressed, the Input list ap-
pears. While the Input list is displayed,
follow the procedure below to switch the
input mode.
– Press
P
/
R
to select the desired input
mode and then press
ENTER
.
•
When “AUTO SEARCH” is selected,
input signal is automatically detected.
•
If
ENTER
is not pressed, the projector
switches to the selected input mode in
a few seconds.
Note
•
When no signal is received, “NO SIGNAL”
will be displayed. When non-supported sig-
nal is received, “NOT REG.” is displayed.
•
The input mode is not displayed when “OSD
Display” of the “Options1” menu is set to
“Level A” or “Level B”. (See page
57
.)
Adjusting the Volume
Press
VOL +/–
on the projector or on
the remote control to adjust the volume.
Note
•
Pressing
VOL–
will lower the volume.
Pressing
VOL+
will raise the volume.
•
When “Pict in Pict” (see page
56
) is set to
“On”, audio volume cannot be adjusted on
the projector. The audio volume buttons will
instead function as location shift button for
the smaller screen.
COMPUTER1/2,
DVI, HDMI, VIDEO
and S-VIDEO buttons
'
/
"
buttons
"
On-screen display
Volume
buttons
Image Projection
Input mode menu