Sanyo PLC-ZM5000L Owners Manual - Page 74

Auto PC adjustment, Some displays are

Get Sanyo PLC-ZM5000L - 5000 Lumens PDF manuals and user guides
UPC - 086483079450
View all Sanyo PLC-ZM5000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Appendix - F ilter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 67-68) appears on the screen - Adjust the focus of the projector. - Check Projection Lens to see if it needs cleaning. The image is out of focus. Note: M oving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such cases, leave the projector OFF and wait until condensation evaporates. - Projecting from excessive slant angle to the screen may cause keystone distortion and partial imperfect focus. The image is not bright enough. - Check if Contrast or Brightness is adjusted properly. (See pages 41, 47) - Check if Image level is selected properly. (See pages 40, 46) - Check the Lamp control function. ( See "Setting" section on page 57) - Check the LAMP REPLACE indicator. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. (See page 69) The color is strange. - Check the Input signal, color system, video system, or computer system mode. - Adjust the Image Level properly. (See pages 40, 46) The image is Left/ Right reversed. - Check the Ceiling / Rear function. (See pages 44, 50) The image is Top/ Bottom reversed. - Check the Ceiling function. (See pages 44, 50) The image is distorted or runs off. - Check PC adjust Menu or Screen Menu and adjust them. Auto PC adjustment function does not work. - Check the Input signal. Auto PC Adjustment function cannot work when 480p, 575p, 720p, 480i, 575i, 1035i, 1080i or 1080p is selected or when the digital signal is input into HDMI or DVI-D terminal. See page 37. Some displays are not seen during the operation. The setting does not remain after turning off power. Power management function does not work. - Check the Display function. (see page 52) - Make sure you selected Store after adjusting settings. Some settings cannot be stored if not registered with Store function. - Power management function cannot work while Freeze function is running or the shutter is closed. Image disappears automatically. - C heck the power management function in the Setting. The power management is set to On at the factory. Capture function does not work. - Check the connection to see if there is signal. - C apture function is not available when the Picture in Picture function is set to User1-5. Some menus cannot be selected. - Each of the Video Input and Computer Input has a limit on selectable menus. No sound - Check the audio cable connection from audio input source. - Adjust the audio source. - Press the Volume + button. ( See page 28) - Press the Mute button. (See page 28) - Is the image projected? You will hear the sound only when the image is projected. - Check the Build-in SP function. (See page 28) 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
appears on the screen
–
Filter is out of scroll. Replace the filter cartridge with a new one promptly.
(See
pages 67-68)
The image is out of
focus°
– Adjust the focus of the projector.
– Check Projection Lens to see if it needs cleaning.
Note:
Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on Projection Lens. In such
cases, leave the projector OFF and wait until condensation evaporates.
–
Projecting from excessive slant angle to the screen may cause keystone distortion
and partial imperfect focus.
The image is not
bright enough°
– Check if
Contrast
or
Brightness
is adjusted properly. (See pages 41, 47)
– Check if
Image level
is selected properly. (See pages 40, 46)
– Check the Lamp control function. ( See “Setting” section on page 57)
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life is approaching.
Replace the lamp with a new one promptly. (See page 69)
The color is strange°
– Check the Input signal, color system, video system, or computer system mode.
– Adjust the Image Level properly. (See pages 40, 46)
The image is Left/
Right reversed°
– Check the Ceiling / Rear function. (See pages 44, 50)
The image is Top/
Bottom reversed°
– Check the Ceiling function. (See pages 44, 50)
The image is distorted
or runs off°
– Check PC adjust Menu or Screen Menu and adjust them.
Auto PC adjustment
function does not
work
.
– Check the Input signal.
Auto PC Adjustment function cannot work when
480p
,
575p
,
720p
,
480i
,
575i
,
1035i
,
1080i
or
1080p
is selected or when the digital signal is input
into HDMI or DVI-D terminal. See page 37.
Some displays are
not seen during the
operation°
– Check the Display function. (see page 52)
The setting does not
remain after turning
off power°
– Make sure you selected
Store
after adjusting settings. Some settings cannot be
stored if not registered with Store function.
Power management
function does not
work°
– Power management function cannot work while Freeze function is running or the
shutter is closed.
Image disappears
automatically°
– Check the power management function in the Setting. The power management is set
to
On
at the factory.
Capture function does
not work°
– Check the connection to see if there is signal.
– Capture function is not available when the Picture in Picture function is set to
User1-5
.
Some menus cannot
be selected°
– Each of the Video Input and Computer Input has a limit on selectable menus.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. ( See page 28)
– Press the Mute button. (See page 28)
– Is the image projected? You will hear the sound only when the image is projected.
– Check the Build-in SP function. (See page 28)
Appendix
74