Rane TTM 56S Operation Manual - Page 9

Torsion spring, Sensors, Remove ribbon, Mark location before, disconnecting ribbon, PGM 1, PGM 2, - mixer

Get Rane TTM 56S PDF manuals and user guides View all Rane TTM 56S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Remove #4 screw Remove #4 screw Mark location before disconnecting ribbon: PGM 1 PGM 2 XFADER Torsion spring Remove ribbon Sensors For more effective cleaning and lubrication, follow the directions outlined below: 1. Required Tool: #1 Philips screwdriver 2. Disconnect the power. 3. Remove knobs from controls covered by the Lexan faceplate. 4. Remove the four, 4-40 screws attaching the Lexan faceplate. 5. Remove the Lexan faceplate. See the picture and instructions below. The rails of the fader are now accessible for normal cleaning and lubrication. 6. Remove fader from mixer if more thorough cleaning is required. 7. NOTE: Do not disturb the position of the small sensors at each end of the Fader. If you do, make sure the parts are standing straight before reinstalling. 8. NOTE: In order to achieve the highest possible accuracy, each magnetic fader is factory calibrated for the location in which it was shipped. If you remove the faders for cleaning, make sure you mark them. This helps you to put them back in the correct location. 9. Remove the fader by removing the two #4 screws securing it. Then disconnect the ribbon cable. 10. Sugary liquids spilled into a fader may be removed by thoroughly rinsing the part in hot water. Make sure the part is clean and dry before lubricating or reinstalling. 11. Removal of grease or other stubborn debris may require alcohol or contact cleaner. Make sure the part is clean and dry before lubricat- ing or reinstalling. 12. To reassemble, reverse the disassembly procedure. 13. Problems? Contact Rane Corporation customer service at 425-355-6000. Manual-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Manual-¹
Torsion spring
Sensors
Remove ribbon
Remove
#4 screw
Remove
#4 screw
Mark location before
disconnecting ribbon:
PGM 1
PGM 2
XFADER
For more effective cleaning and lubrication, follow the directions outlined below:
1. Required Tool: #1 Philips screwdriver
2. Disconnect the power.
3. Remove knobs from controls covered by the Lexan faceplate.
4. Remove the four, 4-40 screws attaching the Lexan faceplate.
5. Remove the Lexan faceplate. See the picture and instructions below. °e rails of the fader are now accessible for normal cleaning and
lubrication.
6. Remove fader from mixer if more thorough cleaning is required.
7.
NOTE:
Do not disturb the position of the small sensors at each end of the Fader
. If you do, make sure the parts are standing straight before
reinstalling.
8.
NOTE
: In order to achieve the highest possible accuracy,
each magnetic fader is factory calibrated
for the location in which it was
shipped. If you remove the faders for cleaning,
make sure you mark them
. °is helps you to put them back in the correct location.
9. Remove the fader by removing the two #4 screws securing it. °en disconnect the ribbon cable.
10. Sugary liquids spilled into a fader may be removed by thoroughly rinsing the part in hot water. Make sure the part is clean and dry
before lubricating or reinstalling.
11. Removal of grease or other stubborn debris may require alcohol or contact cleaner. Make sure the part is clean and dry before lubricat-
ing or reinstalling.
12. To reassemble, reverse the disassembly procedure.
13. Problems? Contact Rane Corporation customer service at 425-355-6000.