Rane AC 23S Operation Manual - Page 4
Ac 23s, Operators Manual - active crossover
View all Rane AC 23S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
OPERATORS MANUAL AC 23S ACTIVE CROSSOVER CH 1 MASTER LEVEL 46 2 8 0 10 LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 MIN MAX 0 10 MIN MAX 0 10 CH 2 MASTER LEVEL 46 2 8 0 10 MONO MASTER SUBWOOFER SUB / LOW MID 4W: MID / HIGH 5W: MID / HIGH-MID MONO 4W OR 5W: INACTIVE LOW 2W: INACTIVE LEVEL 46 MUTE DELAY 46 2 8 2 8 0 10 MIN MAX LOW / MID MID 2W: INACTIVE 2W: LOW FREQUENCY 240 400 LEVEL DELAY 200 600 MUTE 150 750 4 6 46 100 850 80 900 2 8 2 8 70 1k 0 10 MIN MAX MID / HIGH 2W: LOW / HIGH FREQUENCY 700 1.0k 550 2.0k 475 2.8k 350 4.5k 250 5.8k 190 7.0k HIGH LEVEL 46 2 8 0 10 AC 23S ACTIVE CROSSOVER LOW LOW / MID 4W: INACTIVE 5W: HIGH-MID 4W: INACTIVE 5W: HIGH-MID / HIGH HIGH POWER QUICK START Labels above the controls refer to the unit being operated in the 2- or 3-Way Stereo mode. Labels below the controls refer to the unit being operated in the 4- or 5-Way Mono mode. Set the STEREO/MONO switch appropriately. The fact that the AC 23S is a multiple function unit means the outputs are switched around in Mono mode. To operate the unit in Stereo 3-Way mode, be sure the rear panel switches are set for STEREO 3-Way, and the 4W / 5W switch is set for 5-Way. Following the labels above the controls and jacks in logical order, you will find Channel 1 Master Input LEVEL, LOW Output, MID Output, and HIGH Output, with the same for Channel 2. If you need a summed Mono Low Ouput, see 'Monoing the Low Outputs' on page Manual-15. To use the unit as a Mono 5-Way, first check that the Channel 1 and 2 switches are set to 3-WAY, and the push-switch is depressed for MONO. Connect the INPUT source to Channel 1 only. Following the labels below the jacks, look at SUB OUT, then look over at LOW OUT, now go back to MID OUT, then over to HIGH-MID OUT and then proceed to the HIGH OUT. There are two different configurations for Mono 4-Way systems. If your LOW / MID can use a crossover frequency between 70 Hz-1 kHz, see page Manual-7. If your LOW / MID prefers a higher range of 190 Hz-7 kHz, see page Manual-8. In agreement with IEC and AES/ANSI standards, AC 23S wiring convention is pin 2 Positive, pin 3 Negative (return), pin 1 to chassis ground. See the "Sound System Interconnection" RaneNote included with this manual for more information on cabling and grounding requirements. WEAR PARTS: This product contains no wear parts. Manual-1