Panasonic WVSP302 WVSP302 User Guide - Page 44
Unicast port1Image and Unicast port2 Audio, Unicast port1Image] *3
![]() |
View all Panasonic WVSP302 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 44 highlights
[Image quality] Select the image quality of H.264 images from the following. Fine(Image quality priority)/Normal/Low(Motion priority) Default: Normal Note: • When "Constant bit rate" is selected for "Transmission priority", this setting is available. [Refresh interval] Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images. If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264 to diminish image distortions. However, the refresh interval may be longer than the set value. 0.2s/0.33s/0.5s/1s/2s/3s/4s/5s Default: 3s [Transmission type] Select a MPEG-4 transmission type from the following. Unicast port (AUTO): Up to 14 users can access a sin- gle camera concurrently. "Unicast port1(Image)" and "Unicast port2 (Audio)" will automatically be selected when transmitting images and audio from the camera. When it is unnecessary to fix the port number for H.264 image transmission such as when using in a particular LAN environment, it is recommended to select "Unicast port (AUTO)". Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select "Unicast port1(Image)" and "Unicast port2 (Audio)" manually to transmit images and audio from the camera. It is possible to fix the port number of the router used for H.264 image transmission via the Internet by setting "Unicast port (MANUAL)" (☞ page 80). Refer to the operating instructions of the router in use. Multicast: Unlimited number of users can access a single camera concurrently. Complete the entry field of "Multicast address", "Multicast port" and "Multicast TTL/HOPLimit" when transmitting H.264 images with multicast. * Refer to page 7 for further information about the maximum concurrent access number. Default: Unicast port (AUTO) [Unicast port1(Image)] *3 Enter the unicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: H.264(1) 32004 H.264(2) 32014 [Unicast port2(Audio)] *3 Enter the unicast port number (used to transmit audio from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: H.264(1) 33004 H.264(2) 33014 [Multicast address] *4 Enter the multicast IP address. Images and audio will be transmitted to the designated IP address. Available IPv4 address: 224.0.0.0 - 239.255.255.255 Available IPv6 address: Multicast address starting with "FF" Default: H.264(1): 239.192.0.20 H.264(2): 239.192.0.21 Note: • Enter a multicast IP address after checking available multicast address. [Multicast port] *4 Enter the multicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: 37004 Note: • When audio is transmitted from the camera, the port number to be used will be the multicast port number plus "1 000". [Multicast TTL/HOPLimit] *4 Enter the multicast TTL/HOPLimit value. Available value: 1 - 254 Default: 16 44
![](/manual_guide/products/panasonic-wvsp302-wvsp302-user-guide-f68446e/44.png)