Marantz SR6003 SR6003 User Manual - English - Page 34

NAMES AND FUNCTION BASIC CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS ENGLISH 8. Repeat steps 7 until measuring 6 points between the main listening position and surrounding positions. When all measurements end, the following GUI appears on the display. Audyssey MultEQ Setup Speaker Check : OK Calculate 9. Checking Measurement Results When calculations for the measurement results end, a screen appears for confirming the calculation results. Check Result Speakers Config Speakers Size Speakers Distance Channel Level Crossover Frequency Store [Example] Confirmation screen for the distance from speakers to the listening position Speakers Distance Unit Front Left Center Front Right Surround Right Surround Back Right Surround Back Left Surround Left Subwoofer : Feet : 30.0 ft : 19.3 ft : 29.6 ft : 21.5 ft : 12.3 ft : 11.6 ft : 16.3 ft : 12.5 ft Return 10. Storing Measurement Results in Memory Once finished confirming the measurement results, select "Return" with the 3/4 cursor buttons and press the ENTER button to display the Check Result screen. Check Result Speakers Config Speakers Size Speakers Distance Channel Level Crossover Frequency Store : : Enter : OK Exit : Exit Select "Calculate" with the 3/4 cursor buttons and press the ENTER button to calculate measurement results. During calculations, the following GUI appears on the display. Audyssey MultEQ Setup Now Calculating! : : Enter : Exit : Note: • Fewer than 6 positions may be measured, but it is recommended to measure in all 6 positions for best results. Measuring in just one position is not recommended as it does not provide enough acoustical information to the MultEQ algorithm. • The time needed to complete calculations depends on the number of connected speakers and measured listening positions. The more speakers and listening positions, the more time is needed. : Up / Down : Enter : Select Exit : Exit Select items to check with the 3/4 cursor buttons and press the ENTER button to enter them. Note: To check equalizer (MultEQ) parameters, see page 40. [Example] Confirmation screen for speaker detection Speakers Config Check Speaker Results Front Left : Yes Center : No Front Right : Yes Surround Right : Yes Surround Back Right : No Surround Back Left : No Surround Left : Yes Subwoofer : Yes Return : : Enter : Return Exit : Exit [Example] Confirmation screen for speaker size. Speakers Size Front Left Center Front Right Surround Right Surround Back Right Surround Back Left Surround Left : Auto : Auto : Auto : Auto : Auto : Auto : Auto Return : Up / Down : Enter : Return Exit : Exit * The units can be changed by moving the cursor to Meters of Unit and pressing 1 / 2 the cursor buttons. Each time a 1 / 2 cursor button is pressed, the units alternate between Feet and Meters. Note: This system cannot measure a distance of 9.15 m (30.0 ft) or higher. In this case, >9.15 m (>30.0 ft) is displayed. [Example] Confirmation screen for channel level. Channel Level Front Left Center Front Right Surround Right Surround Back Right Surround Back Left Surround Left Subwoofer : 0.0dB : -6.5dB : -1.5dB : +1.0dB : +9.5dB : +12.0dB : -2.5dB : -12.5dB Return : : Enter : Return Exit : Exit [Example] Confirmation screen for crossover frequency. Crossover Frequency Front Center Surround Surround Back : Auto : Auto : Auto : Auto Return : Up / Down : Enter : OK Exit : Exit Place the cursor on "Store" and press the ENTER button to store all parameters including the equalizer parameters in memory. If not wanting to store the calculation results in memory, press the Exit button. Note: Pressing "Exit" prior to pressing "Store" erases all measurement results and calculation results, therefore operate the remote controller with care. When storing operations end, the following GUI appears on the display. Speaker Setup Auto Setup Manual Setup Return : Up / Down : Enter : Select Exit : Exit Notes: • Do not turn the power to the unit off while storing parameters in memory. This may erase all data in the unit's memory and may damage the unit. : : Enter : Return Exit : Exit : : Enter : Return Exit : Exit * Auto is displayed to indicate that the speaker size and crossover frequency results were automatically measured. SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 31