Marantz MODEL 30 User Guide English - Page 37

Operations cannot be performed through the remote control unit, Display on this unit shows nothing

Get Marantz MODEL 30 PDF manuals and user guides View all Marantz MODEL 30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Contents Connections Playback Settings Tips Appendix Operations cannot be performed through the remote control unit Operations cannot be performed through the remote control unit. 0 Batteries are worn out. Replace with new batteries. (v p. 5) 0 Operate the remote control unit within a distance of about 23 ft/7 m from this unit and at an angle of within 30°. (v p. 5) 0 Remove any obstacle between this unit and the remote control unit. 0 Insert the batteries in the proper direction, checking the q and w marks. (v p. 5) 0 The set's remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc.). Move the set to a place in which the remote control sensor will not be exposed to strong light. 0 When using a 3D video device, the remote control unit of this unit may not function due to effects of infrared communications between units (such as TV and glasses for 3D viewing). In this case, adjust the direction of units with the 3D communications function and their distance to ensure they do not affect operations from the remote control unit of this unit. 0 The remote control code of the volume buttons on the remote control (VOLUME no and :) is set to the mode for operating a Marantz Network SACD player. If the volume of this unit cannot be adjusted using the remote control, press and hold ENTER and the number 1 button together for 5 seconds or more to change the remote control code to AMP operation mode. 0 When the remote control code setting is set to "AMP1" (Default), the INPUT ml buttons on the remote control cannot be used to switch the input source to "PWR AMP" or switch from "PWR AMP" to another input source. To make remote control operations, change the remote control code setting to "AMP2" or "AMP3". (v p. 31) 0 The remote control code between this unit and the remote control is different. Set this unit and the remote control to the same remote control code. (v p. 31) Display on this unit shows nothing Display is off. 0 Press the DIMMER button, and change the setting to anything other than off. (v p. 28) Front panel Rear panel Remote control 37 unit Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
Operations cannot be performed through the remote control unit
Operations cannot be performed through the remote control unit.
0
Batteries are worn out. Replace with new batteries.
(
v
p. 5)
0
Operate the remote control unit within a distance of about 23 ft/7 m from this unit and at an angle of within 30°.
(
v
p. 5)
0
Remove any obstacle between this unit and the remote control unit.
0
Insert the batteries in the proper direction, checking the
q
and
w
marks.
(
v
p. 5)
0
The set’s remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc.). Move the set to a place in which the
remote control sensor will not be exposed to strong light.
0
When using a 3D video device, the remote control unit of this unit may not function due to effects of infrared communications between units (such as TV
and glasses for 3D viewing). In this case, adjust the direction of units with the 3D communications function and their distance to ensure they do not
affect operations from the remote control unit of this unit.
0
The remote control code of the volume buttons on the remote control (VOLUME
no
and
:
) is set to the mode for operating a Marantz Network
SACD player. If the volume of this unit cannot be adjusted using the remote control, press and hold ENTER and the number 1 button together for 5
seconds or more to change the remote control code to AMP operation mode.
0
When the remote control code setting is set to “AMP1” (Default), the INPUT
ml
buttons on the remote control cannot be used to switch the input
source to “PWR AMP” or switch from “PWR AMP” to another input source. To make remote control operations, change the remote control code setting
to “AMP2” or “AMP3”.
(
v
p. 31)
0
The remote control code between this unit and the remote control is different. Set this unit and the remote control to the same remote control code.
(
v
p. 31)
Display on this unit shows nothing
Display is off.
0
Press the DIMMER button, and change the setting to anything other than off.
(
v
p. 28)
Contents
Connections
Playback
Settings
Tips
Appendix
37
Front panel
Rear panel
Remote control
unit
Index