Marantz MODEL 30 User Guide English - Page 25

Playing CDs, Using this unit as a power amplifier

Get Marantz MODEL 30 PDF manuals and user guides View all Marantz MODEL 30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Contents Connections Playback Playing CDs This section uses playback from a CD as an example. 1 Press AMP X to turn the power on. 2 Use INPUT ml to switch the input source to "CD". "CD" is displayed on the display. 3 Playback the CD. 4 Use VOLUME no to adjust the volume. Settings Tips Appendix Using this unit as a power amplifier When connecting a pre-amplifier and using this unit as a power amplifier, switch the input source of this unit to "PWR AMP". 1 Turn the INPUT selector on the main unit to switch the input source to "PWR AMP". "PWR AMP" is displayed on the display. 0 When the input source is "PWR AMP", adjustment of the volume, balance and tone has no effect. Adjust these adjustments on the pre-amplifier. 0 When the remote control code setting is set to "AMP1" (Default), INPUT ml on the remote control cannot be used to switch the input source to "PWR AMP" or switch from "PWR AMP" to another input source. To make remote control operations, change the remote control code setting to "AMP2" or "AMP3". (v p. 31) NOTE 0 When the input source is "PWR AMP", the main unit outputs at maximum volume. Check the output level on the input device before playing it and adjust the volume accordingly. Front panel Rear panel Remote control 25 unit Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
Playing CDs
This section uses playback from a CD as an example.
1
Press AMP
X
to turn the power on.
2
Use INPUT
ml
to switch the input source to “CD”.
“CD” is displayed on the display.
3
Playback the CD.
4
Use VOLUME
no
to adjust the volume.
Using this unit as a power amplifier
When connecting a pre-amplifier and using this unit as a power amplifier,
switch the input source of this unit to “PWR AMP”.
1
Turn the INPUT selector on the main unit to switch the
input source to “PWR AMP”.
“PWR AMP” is displayed on the display.
0
When the input source is “PWR AMP”, adjustment of the volume, balance and
tone has no effect. Adjust these adjustments on the pre-amplifier.
0
When the remote control code setting is set to “AMP1” (Default), INPUT
ml
on
the remote control cannot be used to switch the input source to “PWR AMP” or
switch from “PWR AMP” to another input source. To make remote control
operations, change the remote control code setting to “AMP2” or “AMP3”.
(
v
p. 31)
NOTE
0
When the input source is “PWR AMP”, the main unit outputs at maximum volume.
Check the output level on the input device before playing it and adjust the volume
accordingly.
Contents
Connections
Playback
Settings
Tips
Appendix
25
Front panel
Rear panel
Remote control
unit
Index