LiftMaster CSW24UL Installation Manual - Page 28

OPERATION, Gate operator setup examples

Page 28 highlights

OPERATION Gate operator setup examples The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices. RESIDENTIAL: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns COMMERCIAL/GENERAL ACCESS: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access trumps security concerns COMMERCIAL: Business site where security (gate closed) is important INDUSTRIAL: Large business site where security is required SETTING RESIDENTIAL COMMERCIAL/GENERAL ACCESS COMMERCIAL INDUSTRIAL Quick Close switch setting Normally set to OFF. Normal gate Normally set to OFF. Normal gate Normally set to OFF. Normal gate Set to ON, so that gate closes close (timer or control). close (timer or control). close (timer or control). immediately after vehicle passes CLOSE EYES/Interrupt loop. AC Fail Open switch setting Normally set to BATT. Run on battery if AC power fails. Normally set to BATT. For local Normally set to BATT. Run on jurisdiction requirement, set to battery if AC power fails. OPEN so that the gate will open approximately 15 seconds after AC power fail. Normally set to BATT. Run on battery if AC power fails. Low Battery switch setting Normally set to OPEN. If powered Normally set to OPEN. If powered Normally set to CLOSE. If powered Normally set to CLOSE. If powered from battery and battery is low, from battery and battery is low, from battery and battery is low, from battery and battery is low, gate automatically opens and stays gate automatically opens and stays gate stays closed. gate stays closed. open. open. Anti-Tail switch setting Normally set to OFF. CLOSE EYES/Interrupt loop reverses a closing gate. Normally set to OFF. CLOSE EYES/Interrupt loop reverses a closing gate. Set to ON. In attempt to prevent vehicle tail-gating, CLOSE EYES/ Interrupt loop pauses a closing gate. Set to ON. In attempt to prevent vehicle tail-gating, CLOSE EYES/ Interrupt loop pauses a closing gate. Bipart Delay switch setting For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for For DUAL-GATE site, set to ON for gate that delays upon opening. gate that delays upon opening. gate that delays upon opening. gate that delays upon opening. Aux Relay Out - Open Typically not required. Limit Switch Use with SAMS (Sequence Access 1. Use with SAMS (Sequence Management System). Access Management System). 1. Use with SAMS (Sequence Access Management System). 2. Connect "Gate Open" indicator (e.g. light). 2. Connect "Gate Open" indicator (e.g. light). Aux Relay Out - Close Typically not required. Limit Switch Typically not required. Connect "Gate Close/Secure" indicator (e.g. light). Connect "Gate Close/Secure" indicator (e.g. light). Aux Relay Out - Gate Attach alert signal (audible or Motion visual alert system). Attach alert signal (audible or visual alert system). Attach alert signal (audible or visual alert system). Attach alert signal (audible or visual alert system). Aux Relay Out - PreMotion Delay Attach alert signal (audible or visual alert system). Attach alert signal (audible or visual alert system). Attach alert signal (audible or visual alert system). Attach alert signal (audible or visual alert system). Aux Relay Out - Power Attach visual alert to know when system is charging batteries (i.e. not running on batteries). Attach visual alert to know when system is charging batteries (i.e. not running on batteries). Attach visual alert to know when system is charging batteries (i.e. not running on batteries). Attach visual alert to know when system is charging batteries (i.e. not running on batteries). Cycle Quantity Feedback Use during servicing only to determine operator cycles. Use during servicing only to determine operator cycles. Use during servicing only to determine operator cycles. Use during servicing only to determine operator cycles. Fire Dept Open Input Typically not required. Connect emergency access system (Knox box switch, SOS system, etc.). Typically not required. Typically not required. Heater Accessory (Model HTR) The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below -4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation. The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below -4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation. The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below -4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation. The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below -4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

28
Gate operator setup examples
The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site
requirements, including all necessary entrapment protection devices.
RESIDENTIAL:
One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns
COMMERCIAL/GENERAL ACCESS:
A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access
trumps security concerns
COMMERCIAL:
Business site where security (gate closed) is important
INDUSTRIAL:
Large business site where security is required
SETTING
RESIDENTIAL
COMMERCIAL/GENERAL
ACCESS
COMMERCIAL
INDUSTRIAL
Quick Close switch
setting
Normally set to OFF. Normal gate
close (timer or control).
Normally set to OFF. Normal gate
close (timer or control).
Normally set to OFF. Normal gate
close (timer or control).
Set to ON, so that gate closes
immediately after vehicle passes
CLOSE EYES/Interrupt loop.
AC Fail Open switch
setting
Normally set to BATT. Run on
battery if AC power fails.
Normally set to BATT. For local
jurisdiction requirement, set to
OPEN so that the gate will open
approximately 15 seconds after AC
power fail.
Normally set to BATT. Run on
battery if AC power fails.
Normally set to BATT. Run on
battery if AC power fails.
Low Battery switch
setting
Normally set to OPEN. If powered
from battery and battery is low,
gate automatically opens and stays
open.
Normally set to OPEN. If powered
from battery and battery is low,
gate automatically opens and stays
open.
Normally set to CLOSE. If powered
from battery and battery is low,
gate stays closed.
Normally set to CLOSE. If powered
from battery and battery is low,
gate stays closed.
Anti-Tail switch setting
Normally set to OFF. CLOSE
EYES/Interrupt loop reverses a
closing gate.
Normally set to OFF. CLOSE
EYES/Interrupt loop reverses a
closing gate.
Set to ON. In attempt to prevent
vehicle tail-gating, CLOSE EYES/
Interrupt loop pauses a closing
gate.
Set to ON. In attempt to prevent
vehicle tail-gating, CLOSE EYES/
Interrupt loop pauses a closing
gate.
Bipart Delay switch
setting
For DUAL-GATE site, set to ON for
gate that delays upon opening.
For DUAL-GATE site, set to ON for
gate that delays upon opening.
For DUAL-GATE site, set to ON for
gate that delays upon opening.
For DUAL-GATE site, set to ON for
gate that delays upon opening.
Aux Relay Out – Open
Limit Switch
Typically not required.
Use with SAMS (Sequence Access
Management System).
1.
Use with SAMS (Sequence
Access Management
System).
2.
Connect “Gate Open”
indicator (e.g. light).
1.
Use with SAMS (Sequence
Access Management
System).
2.
Connect “Gate Open”
indicator (e.g. light).
Aux Relay Out – Close
Limit Switch
Typically not required.
Typically not required.
Connect “Gate Close/Secure”
indicator (e.g. light).
Connect “Gate Close/Secure”
indicator (e.g. light).
Aux Relay Out – Gate
Motion
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Aux Relay Out – Pre-
Motion Delay
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Attach alert signal (audible or
visualalert system).
Aux Relay Out – Power
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries).
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries).
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries).
Attach visual alert to know when
system is charging batteries (i.e.
not running on batteries).
Cycle Quantity Feedback
Use during servicing only to
determine operator cycles.
Use during servicing only to
determine operator cycles.
Use during servicing only to
determine operator cycles.
Use during servicing only to
determine operator cycles.
Fire Dept Open Input
Typically not required.
Connect emergency access
system (Knox box switch, SOS
system, etc.).
Typically not required.
Typically not required.
Heater Accessory
(Model HTR)
The heater keeps the gearbox and
batteries at a suitable temperature
when the outside temperature is
below -4°F. The thermostat MUST
be set between 45°F and 60°F to
ensure proper gate operation.
The heater keeps the gearbox and
batteries at a suitable temperature
when the outside temperature is
below -4°F. The thermostat MUST
be set between 45°F and 60°F to
ensure proper gate operation.
The heater keeps the gearbox and
batteries at a suitable temperature
when the outside temperature is
below -4°F. The thermostat MUST
be set between 45°F and 60°F to
ensure proper gate operation.
The heater keeps the gearbox and
batteries at a suitable temperature
when the outside temperature is
below -4°F. The thermostat MUST
be set between 45°F and 60°F to
ensure proper gate operation.
OPERATION