LiftMaster 98022 Owners Manual - English French Spanish - Page 16

Connect Power, OPTION B: PERMANENT WIRING, CONNECTION, There are two options for connecting, power

Get LiftMaster 98022 PDF manuals and user guides View all LiftMaster 98022 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

RIGRHIGTHT Installation (continued) WRWORNOGNG PERPMERAMNAENTENWTIRWIINRGING COCNONNECNTEICOTNION 7 Connect Power To avoid installation difficulties, do not run the garage door opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. There are two options for connecting power: GroGurnodunTdabTab GreGerneen GroGurnodunSdcrSecwrew To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: • Be sure power is NOT connected to the opener, and discGoronGunrnoeducnWdtirWpeoirewer to circuit BEFORE removing cover to establish permanent wiring connection. BlaBcklack WirWe ire • Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes. • NEVER use an extension cord, 2-wire adapter or change plug in ANY wayWtohWitmehiWtaeikrWeeireit BlaBckla fit outlet. Be sure the opener is grounded. OPTION A: TYPICAL WIRING 1. Plug in the garage door opener into a grounded outlet. 2. DO NOT run garage door opener at this time. RIGRHIGTHT RIGHT WRWORNOGNG WRONG PERPMERAMNAENTENWTIRWIINRGING COCNONNECNTEICOTNION OPTION B: PERMANENT WIRING CONNECTION If permanent wiring is required by your local code, refer to the following procedure. 1. To make a permanent connection through the 7/8 inch hole in the back of the garage door opener (according to local code): 2. Be sure power is NOT connected to the opener, and disconnect power to circuit. 3. Remove the garage door opener from the torsion bar, remove cover screws and set the cover aside. 4. Cut the line cord 6" (15.2 cm) above the strain relief. 5. Squeeze the strain relief and push into garage door opener, then remove the strain relief from the line cord. 6. Install a 90° conduit (not provided) or flex cable adapter (not provided) to the 7/8" hole. Reinstall garage door opener to torsion bar. 7. Run wires through conduit, cut to proper length and strip insulation. 8. Strip 1/2" (1.3 cm) of insulation from the existing black, white and green wires. 9. Connect the line to the black wire and neutral to the white wire with wire nuts (not provided). Connect ground wire to the green ground screw. 10.Properly secure wires under plastic ties so that they do not come into contact with moving parts. 11.Reinstall cover. GroGurnodunTdabTab GreGerneen GroGurnodunSdcrSecwrew Green Wire 90˚ Connector (Not Provided) GroGBurlnoaducnWkdiWrWe iirree White Wire BlaBcklac WirWe ire WhWitehiWteirWe ire Flexible Conduit BACK VIEW Ground Tab Green Ground Screw Ground Wire Black Wire From Power Cord White Wire From Power Cord 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
16
Ground
Tab
Green Ground
Screw
Ground Wire
Black Wire
From Power
Cord
White Wire
From Power
Cord
Flexible
Conduit
90˚
Connector
(Not
Provided)
Green Wire
White Wire
Black Wire
BACK VIEW
Connect Power
7
OPTION B: PERMANENT WIRING
CONNECTION
If permanent wiring is required by
your local code, refer to the following
procedure.
1. To make a permanent connection
through the 7/8 inch hole in the back
of the garage door opener (according
to local code):
2. Be sure power is NOT connected to
the opener, and disconnect power to
circuit.
3. Remove the garage door opener from
the torsion bar, remove cover screws
and set the cover aside.
4. Cut the line cord 6" (15.2 cm) above
the strain relief.
5. Squeeze the strain relief and push into
garage door opener, then remove the
strain relief from the line cord.
6. Install a 90° conduit (not provided)
or flex cable adapter (not provided)
to the 7/8" hole. Reinstall garage door
opener to torsion bar.
7. Run wires through conduit, cut to
proper length and strip insulation.
8. Strip 1/2" (1.3 cm) of insulation from
the existing black, white and green
wires.
9. Connect the line to the black wire and
neutral to the white wire with wire
nuts (not provided). Connect ground
wire to the green ground screw.
10.Properly secure wires under plastic
ties so that they do not come into
contact with moving parts.
11. Reinstall cover.
To avoid installation difficulties, do not
run the garage door opener at this time.
To reduce the risk of electric shock, your
garage door opener has a grounding type
plug with a third grounding pin. This plug
will only fit into a grounding type outlet. If
the plug doesn’t fit into the outlet you have,
contact a qualified electrician to install the
proper outlet.
There are two options for connecting
power:
OPTION A: TYPICAL WIRING
1.
Plug in the garage door opener into a
grounded outlet.
2.
DO NOT run garage door opener at this
time.
To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:
• Be sure power is NOT connected to the opener, and disconnect power to circuit
BEFORE removing cover to establish permanent wiring connection.
• Garage door installation and wiring MUST be in compliance with ALL local electrical
and building codes.
• NEVER use an extension cord, 2-wire adapter or change plug in ANY way to make it
fit outlet. Be sure the opener is grounded.
RIGHT
WRONG
WRONG
RIGHT
Installation
(continued)