Jenn-Air JUCFP242HX Owners Manual - Page 6

Installation Requirements

Get Jenn-Air JUCFP242HX PDF manuals and user guides View all Jenn-Air JUCFP242HX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. TOOLS AND PARTS NEEDED:  Phillips screwdriver  Cordless drill  1/8" Drill bit  Tape measure  Level ADDITIONAL TOOLS NEEDED (CUSTOM OVERLAY PANEL ONLY):  Scissors  Pencil  Scribe PARTS NEEDED (CUSTOM OVERLAY PANEL ONLY):  Custom Overlay Drawer Panels - See "Custom Overlay Drawer Panels."  Hardware PARTS NEEDED (CUSTOM OVERLAY PANEL ONLY):  Hooks (8)  Screws (16)  Self-tap wood screws (4) LOCATION REQUIREMENTS WARNING NOTES:  For the refrigerator drawers to be flush with the front of the base cabinets remove any baseboards or moldings from the rear of the opening. See "Product Dimensions" and later in this section "Opening Dimensions"  It is recommended that you do not install the refrigerator drawers near an oven, radiator, or other heat source.  Do not install in a location where the temperature will fall below 55°F (13°C). OPENING DIMENSIONS  Height dimensions are shown with the leveling legs extended to the minimum height of 1/4" (6 mm) below the refrigerator drawers. NOTE: When leveling legs are fully extended to 1" (25 mm) below the refrigerator drawers, add 3/4" (19 mm) to the height dimensions. See "Product Dimensions."  If the floor of the opening is not level with the kitchen floor, shim the opening to make it level with the kitchen floor. 143/4" (375 mm) A 1/2" (13 mm) 343/8" (873 mm) min. 35" (889 mm) max. Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from refrigerator drawer(s). Failure to do so can result in death, explosion, or fire. IMPORTANT: This appliance is intended to be used in household and similar applications such as:  Staff kitchen areas in shops, office and other working environments;  Farm houses and by clients in hotels, motels and other residential type environments;  Bed and breakfast type environments;  Catering and similar non-retail applications. 24" (609.6 mm) min. B 24" (609.6 mm) min. Critical Dimensions: A. Utility opening B. Minimum opening width 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
6
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting
installation.
Read and follow the instructions provided with any tools
listed here.
TOOLS AND PARTS NEEDED:
±
Phillips screwdriver
±
Cordless drill
±
1/8" Drill bit
±
Tape measure
±
Level
ADDITIONAL TOOLS NEEDED ±CUSTOM OVERLAY
PANEL ONLY²:
±
Scissors
±
Pencil
±
Scribe
PARTS NEEDED ±CUSTOM OVERLAY PANEL ONLY²:
±
Custom Overlay Drawer Panels — See “Custom
Overlay Drawer Panels.”
±
Hardware
PARTS NEEDED ±CUSTOM OVERLAY PANEL ONLY²:
±
Hooks (8)
±
Screws (16)
±
Self-tap wood screws (4)
LOCATION REQUIREMENTS
IMPORTANT:
This appliance is intended to be used in
household and similar applications such as:
±
Staff kitchen areas in shops, office and other working
environments;
±
Farm houses and by clients in hotels, motels and
other residential type environments;
±
Bed and breakfast type environments;
±
Catering and similar non-retail applications.
NOTES:
±
For the refrigerator drawers to be flush with the
front of the base cabinets remove any baseboards or
moldings from the rear of the opening. See “Product
Dimensions” and later in this section “Opening
Dimensions”
±
It is recommended that you do not install the
refrigerator drawers near an oven, radiator, or other
heat source.
±
Do not install in a location where the temperature will
fall below 55°F (13°C).
OPENING DIMENSIONS
±
Height dimensions are shown with the leveling legs
extended to the minimum height of 1/4" (6 mm)
below the refrigerator drawers.
NOTE:
When leveling legs are fully extended to 1" (25
mm) below the refrigerator drawers, add 3/4" (19 mm)
to the height dimensions. See “Product Dimensions.”
±
If the floor of the opening is not level with the kitchen
floor, shim the opening to make it level with the
kitchen floor.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator drawer(s).
Failure to do so can result in death, explosion, or fire.
Critical Dimensions:
A. Utility opening
B. Minimum opening width
B
A
14±/²"
(375 mm)
1³2"
(13 mm)
34
±/´" (
873 mm) min.
35" (889 mm) max.
24" (609.6 mm) min.
24" (609.6 mm) min.