Intermec IF61 Model IM5 & IF4 865 MHz and 869 MHz Compliance Insert - Page 2

For Users Within North and South America This product is not authorized for use. À l'attention des utilisateurs en Amérique du Nord et du Sud Ce produit n'est pas approuvé pour utilisation. Para usuários das Américas do Norte e do Sul Este produto não está aprovado para uso. Para usuarios dentro de América del Norte y del Sur Este producto no está aprobado para el uso. For Users In All Other Regions 865 MHz Compliance Information Hereby, Intermec Technologies Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product has been assessed to the following standards: • ETSI EN 302 208 • ETSI EN 301 489 • EN 60950-1 For ETSI installations, ETSI EN 302 208 Limits The effective radiated power (e.r.p.) on each of the four high power channels shall not exceed 33 dBm e.r.p. The beamwidth(s) of the antenna(s) in the horizontal orientation shall comply with the following limits: • For transmissions ≤ 500 mW e.r.p. there shall be no restriction on beamwidth. • For transmissions of > 500 mW e.r.p. to ≤ 1 000 mW e.r.p. beamwidths shall be ≤ 180º. • For transmissions of > 1 000 mW e.r.p. to 2 000 mW e.r.p. beamwidths shall be ≤ 90º. The installer will be required to adjust the power output of the IM5/IF4 down if using the following antennas: These settings require the use of Intermec RF cables with 2.4 dB minimum loss. Antenna position indicators must be observed to comply with horizontal beamwidth limits. ≤ 90º Beamwidth Antennas ≤ 2 Watts e.r.p Huber Suhner, SPA/860/70/8/0/V - Max power output 29 dBm Wide Beamwidth Antennas ≤ 500 mW e.r.p NeWave 7 ft - Max power output 26 dBM NeWave 5 ft - Max power output 27 dBm NeWave 3 ft - Max power output 28 dBm Antennas with less than 7 dBi linear gain and ≤ 90º beamwidth can be used with power setting to maximum (30 dBm). Intermec RF cables with 2.4 dB minimum loss are required. 0981 This product is marked with this logo and uses radio frequency bands that are not harmonized throughout the European Community. Refer to the product label for clarification. RF Radiation Exposure Statement Warning: CENELEC regulations limit exposure to radio frequency (RF) radiation. To comply with these regulations, operators of this device must maintain a distance of at least 25.4 cm (10 in) from the antenna assembly. While the device is on, the operator's body and parts of the body such as eyes, hands, or head, must be 25.4 cm (10 in) or farther from the cover of the antenna assembly. Warning: CENELEC regulations also require that the antenna assembly of this device be installed in accordance with the installation procedures to allow the operator to comply with the limit. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment. The transmitter maximum output power is 2 W. The products using this module are intended for business and industrial environments. They should not be used in residential environments and by children. RFID 865 MHz per ETSI EN 302 208: The transmitter output power is 2.0 mW ERP. The following table indicates the areas of intended use of the equipment and any known restrictions (revision REC7003E200903, Annex 11 Band B2). Country of CEPT Intended Use Abbreviation Yes No Austria AUT X Belgium BEL X Bulgaria BUL X Cyprus CYP X Czech Republic CZE X Denmark DNK X Estonia EST X Finland FIN X License Required Restrictions Details 2