Dell PowerEdge M1000e Fabric OS Release Notes - Page 17

Blade Support

Get Dell PowerEdge M1000e PDF manuals and user guides View all Dell PowerEdge M1000e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Blade Support Fabric OS v6.4 software is fully qualified and supports the blades for the 48000 platform noted in the following table: 48000 Blade Support Matrix Port blade 16, 32 and 48-port 4Gbit blades (FC4-16, FC4-32, FC4-48), 16, 32 and 48-port 8Gbit blade (FC8-16, FC8-32, FC8-48), and the 6-port 10G FC blade (FC10-6) Supported with any mix and up to 8 of each. No restrictions around intermix. The 48000 must run Fabric OS v6.0 or later to support the FC8-16 port blade and Fabric OS v6.1 or later to support the FC8-32 and FC8-48 port blades. Note: FC8-64 is not supported on 48000. Intelligent blade Up to a total of 4 Intelligent blades (includes iSCSI, FCIP/FCR and Application blade), FC4-16IP, FR4-18i, and FA4-18 respectively. See below for intermix limitations, exceptions, and a max of each blade. iSCSI blade (FC4-16IP) Up to a maximum of 4 blades of this type. FC-IP/FC Router blade (FR4-18i) Up to a maximum of 2 blades of this type. This can be extended under special circumstances but must be approved by Brocade's Product Team. Up to 8 FR4-18i blades can be installed if they are used only for FC FastWrite or FCIP without routing. Virtualization/Application Blade (FA4-18) Up to a maximum of 2 blades of this type. Encryption Blade (FS8-18), Extension Blade (FX8-24), FCoE/CEE Blade (FCOE10-24) Not supported. Fabric OS v6.4 software is fully qualified and supports the blades for the DCX/DCX-4S noted in the following table: DCX/DCX-4S Blade Support Matrix 16-, 32, 48 and 64-port 8Gbit port blades (FC816, FC8-32, FC8-48, FC8-64) and the 6-port 10G FC blade (FC10-6) 16, 32 and 48 port blades are supported with FOS v6.0 and above, 64 port blade is supported starting with FOS v6.4.0, with any mix and up to 8/4 of each. No restrictions around intermix. Intelligent blade Up to a total of 8/4 intelligent blades. See below for maximum supported limits of each blade. FC-IP/FC Router blade (FR4-18i) Up to a maximum of 4 blades of this type. This can be extended under special circumstances, but must be approved by Brocade's Product Team. Up to 8 FR4-18i blades can be installed in a DCX if they are used only for FC FastWrite or FCIP without routing. Virtualization/Application Blade (FA4-18) Up to a maximum of 4 blades of this type. Fabric OS v6.4.1 Release Notes v1.0 Page 17 of 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
Fabric OS v6.4.1 Release Notes v1.0
Page 17 of 62
Blade Support
Fabric OS v6.4 software is fully qualified and supports the blades for the 48000 platform noted in the
following table:
48000 Blade Support Matrix
48000 Blade Support Matrix
48000 Blade Support Matrix
48000 Blade Support Matrix
Port blade 16, 32 and 48-port 4Gbit blades
(FC4-16, FC4-32, FC4-48), 16, 32 and 48-port
8Gbit blade (FC8-16, FC8-32, FC8-48), and the
6-port 10G FC blade (FC10-6)
Supported with any mix and up to 8 of each.
No
restrictions around intermix.
The 48000 must run Fabric
OS v6.0 or later to support the FC8-16 port blade and
Fabric OS v6.1 or later to support the FC8-32 and FC8-48
port blades.
Note:
Note:
Note:
Note: FC8-64 is not supported on 48000.
Intelligent blade
Up to a total of 4 Intelligent blades (includes iSCSI,
FCIP/FCR and Application blade), FC4-16IP, FR4-18i, and
FA4-18 respectively.
See below for intermix limitations,
exceptions, and a max of each blade.
iSCSI blade (FC4-16IP)
Up to a maximum of 4 blades of this type.
FC-IP/FC Router blade (FR4-18i)
Up to a maximum of 2 blades of this type.
This can be
extended under special circumstances but must be
approved by Brocade’s Product Team.
Up to 8 FR4-18i
blades can be installed if they are used only for FC
FastWrite or FCIP without routing.
Virtualization/Application Blade (FA4-18)
Up to a maximum of 2 blades of this type.
Encryption Blade (FS8-18), Extension Blade
(FX8-24), FCoE/CEE Blade (FCOE10-24)
Not supported.
Fabric OS v6.4 software is fully qualified and supports the blades for the DCX/DCX-4S noted in the following
table
:
DCX/DCX
DCX/DCX
DCX/DCX
DCX/DCX-4S Blade Support Matrix
4S Blade Support Matrix
4S Blade Support Matrix
4S Blade Support Matrix
16-, 32, 48 and 64-port 8Gbit port blades (FC8-
16, FC8-32, FC8-48, FC8-64) and the 6-port 10G
FC blade (FC10-6)
16, 32 and 48
port blades are supported with FOS v6.0
and above, 64 port blade is supported starting with FOS
v6.4.0,
with any mix and up to 8/4 of each.
No restrictions around intermix.
Intelligent blade
Up to a total of 8/4 intelligent blades.
See below for
maximum supported limits of each blade.
FC-IP/FC Router blade (FR4-18i)
Up to a maximum of 4 blades of this type.
This can be
extended under special circumstances, but must be
approved by Brocade’s Product Team.
Up to 8 FR4-18i
blades can be installed in a DCX if they are used only for
FC FastWrite or FCIP without routing.
Virtualization/Application Blade (FA4-18)
Up to a maximum of 4 blades of this type.