D-Link DWL-7620AP User Manual - Page 35

Unified Access Point Administrator’s Guide

Unified Access Point Administrator’s Guide

Page 35

October 2017

Section 3 - Viewing Access Point Status

Field

Description

Fragments

Received

Count of successfully received MPDU frames of type data or management.

Fragments

Transmitted

Number of transmitted MPDU with an individual address or an MPDU with a multicast

address of type Data or Management.

Multicast Frames

Received

Count of MSDU frames received with the multicast bit set in the destination MAC address.

Multicast Frames

Transmitted

Count of successfully transmitted MSDU frames where the multicast bit is set in the

destination MAC address.

Duplicate Frame

Count

Number of times a frame is received and the Sequence Control field indicates is a duplicate.

Failed Transmit

Count

Number of times an MSDU is not transmitted successfully due to transmit attempts

exceeding either the short retry limit or the long retry limit.

Transmit Retry

Count

Number of times an MSDU is successfully transmitted after one or more retries.

Multiple Retry

Count

Number of times an MSDU is successfully transmitted after more than one retry.

RTS Success Count

Count of CTS frames received in response to an RTS frame.

RTS Failure Count

Count of CTS frames not received in response to an RTS frame.

ACK Failure Count

Count of ACK frames not received when expected.

FCS Error Count

Count of FCS errors detected in a received MPDU frame.

Frames Transmitted

Count of each successfully transmitted MSDU.

WEP Undecryptable

Count

Count of encrypted frames received and the key configuration of the transmitter indicates

that the frame should not have been encrypted or that frame was discarded due to the

receiving station not implementing the privacy option.

Table 16 - Radio Statistics Information

Viewing Email Alert Operational Status

The Email Alert Operational Status page provides information about the email alerts sent based on the syslog

messages generated in the AP. To view the Email Alert Operational Status, click the

Status > Email Alert Status

tab.

To configure the email alerts, see

“Configuring Email Alert” on page

76

.

Figure 16 -

Email Alert Operational Status

The following table describes details about the Email Alert Operational Status.

Field

Description

Email Alert Status

The Email Alert operational status The status is either

Up

or

Down

. The default is

Down

.

Number of Email

Sent

The total number of email sent so far. The range is an unsigned integer of 32 bits. The

default is 0.

Number of Email

Failed

The total number of email failures so far. The range is an unsigned integer of 32 bits. The

default is 0.

Time Since Last

Email Sent

The time since the last email was sent. Time format is used. The default is 00 days 00 hours

00 minutes 00 seconds. The UAP uses the system time to report the information. If an email

has not been sent since the device was reset, the status is not sent.

Table 17 -

Email Alert Status

Section	Page
Figure 1 - Administrator UI Online Help	10
Figure 2 - Web UI Login Prompt	15
Figure 3 - Provide Basic Settings	15
Figure 4 - Command Line Interface (CLI) Connection	18
Figure 5 - Viewing Interface Status	22
Figure 6 - Viewing Events	23
Figure 7 - Viewing Traffic Statistics	25
Figure 8 - Viewing WMF Transmit and Receive Statistics	26
Figure 9 - Viewing Client Association Information	27
Figure 10 - Viewing TSPEC Client Associations	28
Figure 11 - Viewing Rogue and Known Access Points	29
Figure 12 - Managed AP DHCP Information	32
Figure 13 - Viewing TSPEC Status and Statistics	32
Figure 14 - View TSPEC Status and Statistics	33
Figure 15 - View Radio Statistics	34
Figure 16 - Email Alert Operational Status	35
Figure 17 - Modify Ethernet (Wired) settings	36
Figure 18 - Modify IPv6 Tunnel Settings	38
Figure 19 - Modify Wireless Settings	39
Figure 20 - Modify Radio Settings	42
Figure 21 - Scheduler Configuration	48
Figure 22 - Scheduler Configuration (Modify Rule)	49
Figure 23 - Scheduler Association Settings	50
Figure 24 - Modify Virtual Access Point Settings	51
Figure 25 - Modify Virtual Access Point Settings (Static WEP)	54
Figure 26 - Modify Virtual Access Point Settings (IEEE802.1X)	56
Figure 27 - Modify Virtual Access Point Settings (WPA Personal)	57
Figure 28 - Modify Virtual Access Point Settings (WPA Enterprise)	58
Figure 29 - Wireless Multicast Forwarding	60
Figure 30 - Configure WDS Bridges	61
Figure 31 - Configure MAC Authentication	63
Figure 32 - Modify Load Balancing Settings	64
Figure 33 - Configure Managed AP Wireless Switch Parameters	66
Figure 34 - Modify 802.1X Supplicant Authentication Settings	67
Figure 35 - Configure Management Access Control Parameters	68
Figure 36 - Configure Web Server Settings	69
Figure 37 - SNMP Configuration	71
Figure 38 - Set SSH Status	72
Figure 39 - Set Telnet Status	73
Figure 40 - DDP Status Configuration	73
Figure 41 - Modify QoS Queue Parameters	74
Figure 42 - Email Alerts Configuration	77
Figure 43 - Time Settings (NTP)	78
Figure 44 - SNMPv3 Views Configuration	80
Figure 45 - SNMPv3 Groups Configuration	81
Figure 46 - SNMPv3 User Configuration	82
Figure 47 - SNMPv3 Targets Configuration	83
Figure 48 - Manage this Access Point’s Configuration - Save (TFTP)	84
Figure 49 - Manage this Access Point’s Configuration - Save (HTTP)	84
Figure 50 - Confirmation Prompt	85
Figure 51 - Manage this Access Point’s Configuration - Restore (TFTP)	85
Figure 52 - Manage this Access Point’s Configuration - Restore (HTTP)	85
Figure 53 - Rebooting the Access Point	86
Figure 54 - Performing AP Maintenance	86
Figure 55 - Manage Firmware (TFTP)	87
Figure 56 - Manage Firmware (HTTP)	87
Figure 57 - Packet Capture Configuration & Settings	88
Figure 58 - Packet Capture Status	89
Figure 59 - Packet Capture Configuration	89
Figure 60 - Packet File Capture	90
Figure 61 - Remote Packet Capture	91
Figure 62 - Packet Capture File Download	92
Figure 63 - Support Information	92
Figure 64 - Configure Client QoS VAP Settings	93
Figure 65 - Configure Client QoS ACL Settings	95
Figure 66 - Configure Client QoS DiffServ Class Map Settings	101
Figure 67 - Configure Client QoS DiffServ Policy Map Settings	105
Figure 68 - QoS Configuration Status For Associated Clients	106
Figure 69 - Manage Access Points In The Cluster (Passive)	110
Figure 70 - Manage Access Points In The Cluster (Active)	110
Figure 71 - Manage Sessions Associated With The Cluster	113
Figure 72 - Automatically Manage Channel Assignments	114
Figure 73 - View Neighboring Access Points	117
Figure 74 - Viewing Details For A Cluster Member	118
Figure 75 - VAP Configuration from the Web Interface	122
Figure 76 - Radio Configuration from the Web Interface	124
Figure 77 - WDS Configuration from the Web Interface	125
Figure 78 - Clustering APs by Using the Web Interface (Passive)	126
Figure 79 - Clustering APs by Using the Web Interface (Active)	127
Figure 80 - Configuring QoS by Using the Web Interface (ACL Name)	128
Figure 81 - Configuring QoS by Using the Web Interface (Rule1)	128
Figure 82 - Configuring QoS by Using the Web Interface (Rule2)	129
Figure 83 - Configuring QoS by Using the Web Interface (VAP QoS Parameters)	129
Figure 84 - Configuring QoS by Using the Web Interface (Class Map Name)	130
Figure 85 - Configuring QoS by Using the Web Interface (Rule)	130
Figure 86 - Configure Client QoS DiffServ Policy Map Settings (Policy Map Name)	130
Figure 87 - Configure Client QoS DiffServ Policy Map Settings (Rule)	131
Figure 88 - Configure Client QoS VAP Settings	131
Configuring QoS by Using the CLI	132

D-Link DWL-7620AP User Manual - Page 35

Viewing Email Alert Operational Status

Page 35 highlights