Adaptec 2820SA User Guide - Page 63

What do SAS Cables Look Like?, How are Disk Drives Identified in SAS?

Get Adaptec 2820SA - Serial ATA II RAID Controller PDF manuals and user guides
UPC - 760884148969
View all Adaptec 2820SA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter A: Introduction to Serial Attached SCSI (SAS) ● 63 What do SAS Cables Look Like? Internal SAS cables are narrower than internal parallel SCSI cables. The connectors vary in size depending on the number of links they support, from single link connectors to 4-wide (or larger) connectors. Internal fan-out cables (shown in the next figure) let you attach four disk drives to a single 4-wide connector. 4x wide-to-4x wide internal SAS cable Internal SAS-to-SATA fan-out cable (SAS-to-SAS fan-out cables are also available) External SAS cable An example of some internal SAS cables and an external SAS cable are shown in the figure above. How are Disk Drives Identified in SAS? In the BIOS and in the management utilities (see page 52), disk drives are identified with numbers in this format: XX:YY:ZZ where XX is the disk drive count number, YY is the enclosure number, and ZZ is the slot number (within the enclosure). If the disk drive is not installed in an enclosure, a double dashes (--) appear instead of YY and ZZ (for instance, 01:--:--). In parallel SCSI, XX is the disk drive's channel number, YY is the target number, and ZZ is the logical unit number (LUN). What are the SAS Connection Options? You can connect end devices to each other through direct cable connections and through backplane connections. When you use one or more expander devices (see page 64), you can create large configurations. Direct-attach Connections In a direct-attach connection, SAS or SATA disk drives are connected directly to a SAS card with SAS cables. One disk drive is attached to one SAS connector with one SAS cable (or multiple disk drives are attached to one SAS connector with one fan-out cable). The figure on page 62 shows an example of direct-attach connections. The number of direct-attached disk drives is limited to the number of phys supported by the SAS card. (Note that there may be multiple phys within a single connector. See page 63.)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Chapter A: Introduction to Serial Attached SCSI (SAS)
●
63
What do SAS Cables Look Like?
Internal SAS cables are narrower than internal parallel SCSI cables. The connectors vary in size
depending on the number of links they support, from single link connectors to 4-wide (or
larger) connectors. Internal fan-out cables (shown in the next figure) let you attach four disk
drives to a single 4-wide connector.
An example of some internal SAS cables and an external SAS cable are shown in the figure
above.
How are Disk Drives Identified in SAS?
In the BIOS and in the management utilities (see
page 52
), disk drives are identified with
numbers in this format:
XX:YY:ZZ
where XX is the disk drive count number, YY is the enclosure number, and ZZ is the slot
number (within the enclosure). If the disk drive is not installed in an enclosure, a double
dashes (--) appear instead of YY and ZZ (for instance, 01:--:--).
In parallel SCSI, XX is the disk drive’s channel number, YY is the target number, and ZZ is the
logical unit number (LUN).
What are the SAS Connection Options?
You can connect end devices to each other through direct cable connections and through
backplane connections. When you use one or more expander devices (see
page 64
), you can
create large configurations.
Direct-attach Connections
In a direct-attach connection, SAS or SATA disk drives are connected directly to a SAS card
with SAS cables. One disk drive is attached to one SAS connector with one SAS cable (or
multiple disk drives are attached to one SAS connector with one fan-out cable). The figure on
page 62
shows an example of direct-attach connections.
The number of direct-attached disk drives is limited to the number of
phys
supported by the
SAS card. (Note that there may be multiple phys within a single connector. See
page 63
.)
4x wide-to-4x wide internal SAS cable
Internal SAS-to-SATA fan-out cable (SAS-to-SAS fan-out cables are
also available)
External SAS cable