Adaptec 2820SA User Guide - Page 48

Before You Begin, Creating a Driver Disk, For Red Hat or SuSE Linux, see

Get Adaptec 2820SA - Serial ATA II RAID Controller PDF manuals and user guides
UPC - 760884148969
View all Adaptec 2820SA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Chapter 8: Installing the Driver on an Existing Operating System ● 48 Before You Begin Before you begin, install and connect your Adaptec RAID controller and internal disk drives (see page 31). You must also create a driver disk (see page 42) before you begin installing the controller driver. Creating a Driver Disk Note: You will need a floppy disk to complete this task. To create a driver disk: 1 Set your system BIOS so that your computer boots from the CD drive. (For instructions, refer to your computer's documentation.) 2 Turn on your computer, then insert the RAID Installation CD included in your RAID controller kit. 3 Follow the on-screen instructions to get to the Adaptec Start Menu. 4 Click Create Driver Disk, then select your operating system. Linux only-Select your operating system and the architecture: ● Intel 386 or 486 computers-Select i386. ● Pentium I or II computers-Select i586. ● Pentium III, IV, or AMD K-6 computers-Select i686. ● AMD Athlon computers-Select Athlon. 5 Select your floppy disk drive letter, then select the format you want. (You need a full format only if your floppy disk has never been formatted or may have bad sectors.) 6 Insert the floppy disk, then click OK. The system creates the driver disk. 7 Remove and label the driver disk. 8 Continue the driver installation for your operating system: ● For Windows, see page 49. ● For Red Hat or SuSE Linux, see page 49. ● For NetWare, see page 49. ● For OpenServer, see page 50. ● For UnixWare, see page 50. ● For Solaris, see page 51. ● For FreeBSD, see page 51.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Chapter 8: Installing the Driver on an Existing Operating System
●
48
Before You Begin
Before you begin, install and connect your Adaptec RAID controller and internal disk drives
(see
page 31
).
You must also create a driver disk (see
page 42
) before you begin installing the controller driver.
Creating a Driver Disk
Note:
You will need a floppy disk to complete this task.
To create a driver disk:
1
Set your system BIOS so that your computer boots from the CD drive. (For instructions,
refer to your computer’s documentation.)
2
Turn on your computer, then insert the RAID Installation CD included in your RAID
controller kit.
3
Follow the on-screen instructions to get to the Adaptec Start Menu.
4
Click
Create Driver Disk
, then select your operating system.
Linux only—
Select your operating system
and
the architecture:
●
Intel 386 or 486 computers
—Select
i386
.
●
Pentium I or II computers
—Select
i586
.
●
Pentium III, IV, or AMD K-6 computers
—Select
i686
.
●
AMD Athlon computers
—Select
Athlon
.
5
Select your floppy disk drive letter, then select the format you want. (You need a full format
only if your floppy disk has never been formatted or may have bad sectors.)
6
Insert the floppy disk, then click
OK
. The system creates the driver disk.
7
Remove and label the driver disk.
8
Continue the driver installation for your operating system:
●
For Windows, see
page 49
.
●
For Red Hat or SuSE Linux, see
page 49
.
●
For NetWare, see
page 49
.
●
For OpenServer, see
page 50
.
●
For UnixWare, see
page 50
.
●
For Solaris, see
page 51
.
●
For FreeBSD, see
page 51
.