Acer Altos S700 User Manual - Page 92

Installing and Removing an LS Module, Installing an LS Module, Removing an LS Module

Get Acer Altos S700 PDF manuals and user guides View all Acer Altos S700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

76 Chapter 6 Installing and Removing Components Installing and Removing an LS Module The LS Modules are located in the front of the enclosure. Follow these procedures to install and remove the LS Modules. Installing an LS Module 1 Select the LS Module slot in to which the LS Module is to be inserted and remove the LS blank if one is installed. 2 Orient the LS Module such that the LEDs are on the top (on the right for deskside systems). 3 With the cam lever fully open slide the LS Module into the slot until the lever starts to close. 4 Fully close the cam lever. The lever is fully closed, and the LS Module locked in place, when the lever "clicks" into position. Removing an LS Module 1 Using your finger, release the locking tab by pressing it in the direction shown in Figure 5-2, and pull the cam lever towards you. 2 Fully open the cam lever (approx. 90o to enclosure). 3 Gently, pull the LS Module out of the enclosure. Caution: Immediately replace the LS Module to maintain correct airflow.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Chapter 6 Installing and Removing Components
76
Installing and Removing an LS Module
The LS Modules are located in the front of the enclosure. Follow these
procedures to install and remove the LS Modules.
Installing an LS Module
1
Select the LS Module slot in to which the LS Module is to be
inserted and remove the LS blank if one is installed.
2
Orient the LS Module such that the LEDs are on the top (on the
right for deskside systems).
3
With the cam lever fully open slide the LS Module into the slot
until the lever starts to close.
4
Fully close the cam lever. The lever is fully closed, and the LS
Module locked in place, when the lever “clicks” into position.
Removing an LS Module
1
Using your finger, release the locking tab by pressing it in the
direction shown in Figure 5-2, and pull the cam lever towards you.
2
Fully open the cam lever (approx. 90
o
to enclosure).
3
Gently, pull the LS Module out of the enclosure.
Caution
: Immediately replace the LS Module to maintain correct
airflow.