2012 Yamaha Motorsports Grizzly 700 4x4 EPS Owners Manual - Page 53

2012 Yamaha Motorsports Grizzly 700 4x4 EPS Manual

Get 2012 Yamaha Motorsports Grizzly 700 4x4 EPS PDF manuals and user guides View all 2012 Yamaha Motorsports Grizzly 700 4x4 EPS manuals

Page 53 highlights

ECB00163 TIP This model is equipped with an ignition circuit cutoff system. The engine can be started under the following conditions: G The drive select lever is in the neutral or park position. G The rear brake lever or brake pedal is applied with the drive select lever in any position. However, it is recommended to shift into the neutral or park position before starting the engine. 3. Apply the rear brake lever or brake pedal. 4. Completely close the throttle lever and start the engine by pushing the start switch. TIP If the engine fails to start, release the start switch, then push it again. Pause a few seconds before the next attempt. Each cranking should be as short as possible to preserve battery energy. Do not crank the engine more than 10 seconds on each attempt. NOTICE For maximum engine life, never accelerate hard when the engine is cold! EBU20441 Operating the drive select lever and driving in reverse ECB00170 NOTICE Before shifting, stop the ATV, otherwise the transmission may be damaged. Shifting: Neutral to High-range and High-range to Low-range 1. Bring the ATV to a complete stop. 2. Apply the brake pedal, and then shift by moving the drive select lever along the shift guide. TIP Make sure that the drive select lever is completely shifted into position. 6 6-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
6-2
6
TIP
This model is equipped with an ignition circuit cut-
off system. The engine can be started under the
following conditions:
●
The drive select lever is in the neutral or park po-
sition.
●
The rear brake lever or brake pedal is applied
with the drive select lever in any position. How-
ever, it is recommended to shift into the neutral
or park position before starting the engine.
3.
Apply the rear brake lever or brake pedal.
4. Completely close the throttle lever and start
the engine by pushing the start switch.
TIP
If the engine fails to start, release the start switch,
then push it again. Pause a few seconds before
the next attempt. Each cranking should be as short
as possible to preserve battery energy. Do not
crank the engine more than 10 seconds on each
attempt.
NOTICE
ECB00163
For maximum engine life, never accelerate
hard when the engine is cold!
EBU20441
Operating the drive select lever and
driving in reverse
NOTICE
ECB00170
Before shifting, stop the ATV, otherwise the
transmission may be damaged.
Shifting: Neutral to High-range and High-range
to Low-range
1.
Bring the ATV to a complete stop.
2.
Apply the brake pedal, and then shift by mov-
ing the drive select lever along the shift guide.
TIP
Make sure that the drive select lever is completely
shifted into position.