2011 Yamaha Motorsports RS Venture Owners Manual - Page 88

2011 Yamaha Motorsports RS Venture Manual

Get 2011 Yamaha Motorsports RS Venture PDF manuals and user guides View all 2011 Yamaha Motorsports RS Venture manuals

Page 88 highlights

Periodic maintenance and adjustment stick. NOTICE: When adding the engine oil, be careful not to fill above the "H" level mark on the dipstick. Use only the recommended oil. (See page 122.) Make sure that no foreign material enters the engine oil tank. [ECS00462] RS90GT / RS90LTGT / RST90GT 1. O-ring 1 2 TIP Make sure that the O-ring is properly seated. 13. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque. Tightening torque: Oil filter cartridge: 17 Nm (1.7 m·kgf, 12 ft·lbf) 14. Install the engine oil drain bolts and their new gasket, and then tighten the bolts to the specified torques. Tightening torques: Engine oil drain bolt (crankcase): 10 Nm (1.0 m·kgf, 7.2 ft·lbf) Engine oil drain bolt (oil tank): 16 Nm (1.6 m·kgf, 12 ft·lbf) 15. Add 2.0 L (2.11 US qt, 1.76 Imp.qt) of the recommended engine oil to the oil tank, and then install and tighten the oil filler cap and the cylinder head cap. Recommended engine oil: See page 122. 16. Start the engine, warm it up for several minutes, and then turn it off. 17. Remove the oil filler cap, and then add sufficient oil of the recommended type to raise it to the "H" level mark on the dip- 1. "H" level mark 2. "L" level mark RST90 1. "H" level mark 2. "L" level mark 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Periodic maintenance and adjustment
82
TIP
Make sure that the O-ring is properly seated.
13.
Install the new oil filter cartridge with an
oil filter wrench, and then tighten it to the
specified torque.
14.
Install the engine oil drain bolts and their
new gasket, and then tighten the bolts to
the specified torques.
15.
Add 2.0 L (2.11 US qt, 1.76 Imp.qt) of the
recommended engine oil to the oil tank,
and then install and tighten the oil filler
cap and the cylinder head cap.
16. Start the engine, warm it up for several
minutes, and then turn it off.
17. Remove the oil filler cap, and then add
sufficient oil of the recommended type to
raise it to the “H” level mark on the dip-
stick.
NOTICE:
When adding the en-
gine oil, be careful not to fill above the
“H” level mark on the dipstick. Use
only the recommended oil. (See page
122.) Make sure that no foreign materi-
al enters the engine oil tank.
[ECS00462]
RS90GT / RS90LTGT / RST90GT
RST90
1. O-ring
Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torques:
Engine oil drain bolt (crankcase):
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
Engine oil drain bolt (oil tank):
16 Nm (1.6 m·kgf, 12 ft·lbf)
Recommended engine oil:
See page 122.
1.
“H” level mark
2.
“L” level mark
1.
“H” level mark
2.
“L” level mark
1
2