2008 Yamaha Motorsports V Star 250 Owners Manual - Page 74

2008 Yamaha Motorsports V Star 250 Manual

Get 2008 Yamaha Motorsports V Star 250 PDF manuals and user guides View all 2008 Yamaha Motorsports V Star 250 manuals

Page 74 highlights

PERIODIC MAINTENANCE AND MINOR REPAIR EAU32760 1. 2. 3. 4. 5. Axle nut Axle nut cotter pin Chain puller locknut Drive chain slack adjusting nut Alignment marks 1. 2. 3. 4. 5. Brake torque rod Brake torque rod bolt and nut Brake rod Brake pedal free play adjusting nut Brake camshaft lever To install the rear wheel 1. Install the drive chain onto the rear sprocket, and then install the wheel by inserting the wheel axle from the right-hand side. 2. Install the brake rod onto the brake camshaft lever, and then install the brake pedal free play adjusting nut onto the brake rod. 3. Connect the brake torque rod to the brake shoe plate by installing the bolt and nut, and then tighten the bolt to the specified torque. Tightening torque: Brake torque rod bolt: 23 Nm (2.3 m·kgf, 17 ft·lbf) 6 3. Loosen the axle nut and the brake torque rod nut at the brake shoe plate. 4. Lift the rear wheel off the ground according to the procedure on page 6-35. 5. Remove the brake pedal free play adjusting nut, and then disconnect the brake rod at the brake camshaft lever. 6. Disconnect the brake torque rod from the brake shoe plate by removing the nut and the bolt. 7. Push the wheel forward, and then remove the drive chain from the rear sprocket. NOTE: The drive chain does not need to be disassembled in order to remove and install the rear wheel. 8. Remove the axle nut. 9. Pull the wheel axle out, and then remove the wheel. 4. Adjust the drive chain slack. (See page 6-24.) 5. Install the axle nut, and then lower the rear wheel so that it is on the ground. 6. Tighten the axle nut to the specified torque, and then insert a new cotter pin into the axle nut. 6-38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
PERIODIC MAINTENANCE AND MINOR REPAIR
6-38
6
3.
Loosen the axle nut and the brake
torque rod nut at the brake shoe
plate.
4. Lift the rear wheel off the ground
according to the procedure on
page 6-35.
5.
Remove the brake pedal free play
adjusting nut, and then disconnect
the brake rod at the brake cam-
shaft lever.
6. Disconnect the brake torque rod
from the brake shoe plate by re-
moving the nut and the bolt.
7.
Push the wheel forward, and then
remove the drive chain from the
rear sprocket.
NOTE:
The drive chain does not need to be
disassembled in order to remove and
install the rear wheel.
8.
Remove the axle nut.
9.
Pull the wheel axle out, and then
remove the wheel.
EAU32760
To install the rear wheel
1.
Install the drive chain onto the rear
sprocket, and then install the
wheel by inserting the wheel axle
from the right-hand side.
2.
Install the brake rod onto the brake
camshaft lever, and then install the
brake pedal free play adjusting nut
onto the brake rod.
3. Connect the brake torque rod to
the brake shoe plate by installing
the bolt and nut, and then tighten
the bolt to the specified torque.
4.
Adjust the drive chain slack. (See
page 6-24.)
5.
Install the axle nut, and then lower
the rear wheel so that it is on the
ground.
6.
Tighten the axle nut to the speci-
fied torque, and then insert a new
cotter pin into the axle nut.
1.
Axle nut
2.
Axle nut cotter pin
3.
Chain puller locknut
4.
Drive chain slack adjusting nut
5.
Alignment marks
1.
Brake torque rod
2.
Brake torque rod bolt and nut
3.
Brake rod
4.
Brake pedal free play adjusting nut
5.
Brake camshaft lever
Tightening torque:
Brake torque rod bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)