2008 Yamaha Motorsports FX Nytro RTX Owners Manual - Page 63

2008 Yamaha Motorsports FX Nytro RTX Manual

Get 2008 Yamaha Motorsports FX Nytro RTX PDF manuals and user guides View all 2008 Yamaha Motorsports FX Nytro RTX manuals

Page 63 highlights

Periodic maintenance 9. Rotate the secondary sliding sheave clockwise and push it so that it separates from the secondary fixed sheave. 2. Remove the shroud and the right side cover. (See page 43 for removal procedures.) Remove the dipstick, wipe it off with a clean rag, and then screw it back into the filler hole. 3. 1. Secondary sliding sheave 2. Secondary fixed sheave 10. Install the V-belt between the secondary sliding and fixed sheaves. 1. Dipstick 4. Remove the dipstick and check that the oil level is within the range shown at the bottom of the dipstick. If the oil does not reach the bottom of the dipstick, add sufficient oil of the recommended type to raise it to the correct level. 1. V-belt 11. Install the drive guard, and then install the left side cover and the shroud. ESU12830 Drive chain housing EWS00430 WARNING The engine, oil tank, brake disc, and coolant hoses will be very hot after the engine has been run. Avoid contact while they are still hot with any part of your body or clothing during inspection or repair. To check the drive chain housing oil level 1. Place the snowmobile on a level surface. 1. Oil level range (FX10RT / FX10MT) 2. Oil level range (FX10 / FX10RTR / FX10RTRA / FX10MTR / FX10MTRA) 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Periodic maintenance
57
9.
Rotate the secondary sliding sheave
clockwise and push it so that it separates
from the secondary fixed sheave.
10.
Install the V-belt between the secondary
sliding and fixed sheaves.
11.
Install the drive guard, and then install the
left side cover and the shroud.
ESU12830
Drive chain housing
WARNING
EWS00430
The engine, oil tank, brake disc, and cool-
ant hoses will be very hot after the engine
has been run. Avoid contact while they are
still hot with any part of your body or cloth-
ing during inspection or repair.
To check the drive chain housing oil level
1.
Place the snowmobile on a level surface.
2.
Remove the shroud and the right side
cover. (See page 43 for removal proce-
dures.)
3.
Remove the dipstick, wipe it off with a
clean rag, and then screw it back into the
filler hole.
4.
Remove the dipstick and check that the
oil level is within the range shown at the
bottom of the dipstick. If the oil does not
reach the bottom of the dipstick, add suf-
ficient oil of the recommended type to
raise it to the correct level.
1.
Secondary sliding sheave
2.
Secondary fixed sheave
1. V-belt
1. Dipstick
1.
Oil level range (FX10RT / FX10MT)
2.
Oil level range (FX10 / FX10RTR /
FX10RTRA / FX10MTR / FX10MTRA)