2007 Yamaha Motorsports Apex Owners Manual - Page 85

2007 Yamaha Motorsports Apex Manual

Get 2007 Yamaha Motorsports Apex PDF manuals and user guides View all 2007 Yamaha Motorsports Apex manuals

Page 85 highlights

E_8fp.book Page 30 Tuesday, March 28, 2006 4:35 PM ESU04092 Adjusting the control rods The weight transfer can be adjusted by turning the control rod adjuster or adjusting nut. For RX10R/RXW10 1. Loosen the locknut 1. 2. Turn the control rod adjuster 2 in direction a to increase weight transfer or direction b to decrease weight transfer. CD-27E Adjuster turning direction Weight transfer a Increased ← ← → b → Decreased 3. Check the adjuster length c using the scale on the special wrench 3 included in the owner's tool kit as shown. Make sure that the rim d of the control rod body is within the range e of the scale. 4. Tighten the locknut while holding the adjuster in place. Locknut tightening torque: 35 Nm (3.5 m·kgf, 25 ft·lb) CAUTION: @ When using the special wrench, make sure that it is situated at a right angle to the control rod, and that it is tightly fitted to the locknut or the control rod adjuster. @ WARNING @ Never adjust the control rod beyond the range of the scale on the special wrench. @ 8-30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
8-30
ESU04092
Adjusting the control rods
The weight transfer can be adjusted by turning the con-
trol rod adjuster or adjusting nut.
For RX10R/RXW10
1. Loosen the locknut
1
.
2. Turn the control rod adjuster
2
in direction
a
to
increase weight transfer or direction
b
to decrease
weight transfer.
CD-27E
3. Check the adjuster length
c
using the scale on the
special wrench
3
included in the owner’s tool kit as
shown. Make sure that the rim
d
of the control rod
body is within the range
e
of the scale.
4. Tighten the locknut while holding the adjuster in
place.
CAUTION
:
@
When using the special wrench, make sure that it is
situated at a right angle to the control rod, and that it
is tightly fitted to the locknut or the control rod
adjuster.
@
WARNING
@
Never adjust the control rod beyond the range of the
scale on the special wrench.
@
Adjuster turning
direction
a
←
→
b
Weight transfer
Increased
←
→
Decreased
Locknut tightening torque:
35 Nm (3.5 m·kgf, 25 ft·lb)
E_8fp.book
Page 30
Tuesday, March 28, 2006
4:35 PM