2005 Yamaha Motorsports SXVenom Owners Manual - Page 69

2005 Yamaha Motorsports SXVenom Manual

Get 2005 Yamaha Motorsports SXVenom PDF manuals and user guides View all 2005 Yamaha Motorsports SXVenom manuals

Page 69 highlights

8. Install the V-belt over the primary sheave assembly. 9. Rotate the secondary sliding sheave clockwise 6 and push 7 it so that it separates from the secondary fixed sheave. 10. Install the V-belt 8 between the secondary sliding and secondary fixed sheaves. 11. Install the drive guard. WARNING @ Never run the engine with the V-belt or drive guard removed. @ ESU01712 Checking the drive chain housing oil level and the drive chain tension Oil level check WARNING @ The engine and muffler will be very hot after the engine has been run. Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair. @ 1. Place the snowmobile on a level surface. 2. Remove the dipstick 1 and wipe it off with a clean rag. Then, put the dipstick in the hole. CAUTION: @ There is a magnet attached to the end of the dipstick. It is used to remove any metal particles that may accumulate in the drive chain housing. When removing the dipstick, be sure to: G Pull it out slowly and gently so the metal particles do not fall off the magnet back into the drive chain housing. G Wipe off the magnet before reinserting the dipstick into the drive chain housing. @ 8-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
8-15
8. Install the V-belt over the primary sheave assembly.
9. Rotate the secondary sliding sheave clockwise
6
and push
7
it so that it separates from the secondary
fixed sheave.
10. Install the V-belt
8
between the secondary sliding
and secondary fixed sheaves.
11. Install the drive guard.
WARNING
@
Never run the engine with the V-belt or drive guard
removed.
@
ESU01712
Checking the drive chain housing oil level and
the drive chain tension
Oil level check
WARNING
@
The engine and muffler will be very hot after the
engine has been run. Avoid touching the engine and
muffler while they are still hot with any part of your
body or clothing during inspection or repair.
@
1. Place the snowmobile on a level surface.
2. Remove the dipstick
1
and wipe it off with a clean
rag. Then, put the dipstick in the hole.
CAUTION
:
@
There is a magnet attached to the end of the dipstick.
It is used to remove any metal particles that may
accumulate in the drive chain housing. When remov-
ing the dipstick, be sure to:
●
Pull it out slowly and gently so the metal particles
do not fall off the magnet back into the drive
chain housing.
●
Wipe off the magnet before reinserting the dip-
stick into the drive chain housing.
@