2007 Polaris Outlaw 90 Owners Manual - Page 157
2007 Polaris Outlaw 90 Manual
Page 157 highlights
Maintenance Drive Chain Slack 1. Check the amount of chain slack by moving the vehicle slightly forward to gain slack at the top side of the chain. 2. Collapse the suspension with an adjustable (buckle type) trailer tie-down strap. Fasten the strap around the axle and rear bumper tube. 3. Tighten the strap until a straight line can be drawn from the rear axle to the gearcase output shaft intersecting the swing arm pivot. This establishes the tightest chain position. 4. Pull down on the chain tensioner to move it out of the way, then measure chain slack. It should Strap have 1/4"-1/2" (6-12 mm) deflection. Chain 5. If the chain needs adjustment, Tensioner use the procedure on page 155. 154
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152 -
153 -
154 -
155 -
156 -
157 -
158 -
159 -
160 -
161 -
162 -
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
 |
 |
154
Maintenance
Drive Chain Slack
1.
Check the amount of chain slack by moving the vehicle slightly forward to gain slack at
the top side of the chain.
2.
Collapse the suspension with an adjustable (buckle type) trailer tie-down strap. Fasten
the strap around the axle and rear bumper tube.
3.
Tighten the strap until a straight
line can be drawn from the rear
axle to the gearcase output shaft
intersecting the swing arm pivot.
This establishes the tightest
chain position.
4.
Pull down on the chain tensioner
to move it out of the way, then
measure chain slack. It should
have 1/4"-1/2" (6-12 mm)
deflection.
5.
If the chain needs adjustment,
use the procedure on page 155.
Strap
Chain
Tensioner