Marantz ST-17 ST-17 User Manual - Page 11
System Remote Control Unit - fm tuner
View all Marantz ST-17 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
FRANÇAIS ENGLISH The battery life is about 1 year under normal use. The life is depended on the operating condition. Take the battery out of the unit when it is not to be used for a long period of time. Keep the battery out of reach of children. If it is swallowed, immediately call the doctor. Caution on battery Improper use of battery may lead to fluid leakage or battery explosopn. Use special care in the following points when handling a battery. ¼ Insert the battery with correct position and negative polarity as indicated on the equipment. ¼ A used battery should be disposed of in the battery disposal box installed in your dealer. Additional description on remote control bus terminal If it is required to connect this unit to other MARANTZ equipment equipped with REMOTE CONTROL terminals and control both pieces of equipment as a system, change the remote control signal which can operate this unit to the signal from the REMOTE CONTROL input terminal by performing the following procedure before connecting this unit with other equipment. Without this procedure, the system control of this unit is impossible even when it is connected through the REMOTE CONTROL terminal. The following procedure is not required if the system connection through the REMOTE CONTROL terminal is not used. SYSTEM REMOTE CONTROL UNIT When the ST-17 is connected with the PM-17 through a system control cord, the ST-17 can be controlled as a part of system using the RC17PM system remote control unit provided with the PM-17. CONTROLS OF THE SYSTEM REMOTE CONTROL UNIT (RC-17PM) PRESET UP/DOWN buttons REPEAT PHONO CD RANDOM TAPE 1 LINE 1 /TUNER +/A TAPE 2 LINE 2 /TV -/B LINE 3 /DVD 1 2 3 4 5 6 7 8 9 0 BAND button Number buttons 1. Set the POWER switch to the off position and, while holding the BAND and DISPLAY buttons simultaneously, press the POWER switch to ON. 2. " " blinks for 2 seconds on the display, indicating that the remote control of this unit will thereafter be based on the external signal input through the REMOTE CONTROL terminal. In this case, the IR sensor of the main unit will no longer accept the signals from the remote control unit. The remote control unit should be pointed to the IR sensor of the equipment connected to this unit. * To return to the initial condition, perform the same operation as step 1 above. " " blinks for 2 seconds on the display and the remote control condition returns to the initial condition. TUNING DOWN button OPEN /CLOSE VOLUME TUNING UP button Press the LINE 1/TUNER button to switch the input selector of the PM17. BAND BUTTON (LINE 1/TUNER) Use this button to select FM or AM wave bands. NUMERIC BUTTONS (0 to 9) Use these buttons to preset receiving frequencies in the memory or to recall the preset frequencies from the memory (Preset tuning). Up tp 30 stations in the FM and AM bands can be preset in the memory in a random order. For operation of the preset memory, refer to "PERSET TUNING". The PRESET number indicator lights up when a preset button is pressed. These buttons are also used as the character entry buttons in the station-name input mode. * The buttons used in the station name operation are identical to the RC-17ST (see page 7). TUNING UP(ǠǠ)/DOWN(ǡǡ) BUTTON Every time the UP or DOWN side of the TUNING button is pressed, the receiving frequency varies in the upward or downward direction, in the step of 50 kHz in FM band or 9 kHz in AM band. When the button is held depressed for more than 0.5 seconds, the receiving frequency varies continuously in the above-mentioned steps until a station is received. Press or hold the button until the desired frequency is displayed on the digital frequency indicator. PRESET UP(ѿ/A)/DOWN(Ҁ/B) BUTTON Every time the UP or DOWN side of the PRESET button is pressed, the preset number will advance one step in the upward or downward direction. The unused preset numbers without memory contents are skipped. This button is also as the CURSOR button in the station name input mode. 9