Stihl HL 100 K 0186 Product Instruction Manual - Page 19

Fueling, Adjusting the Cutter Bar

Get Stihl HL 100 K 0186 PDF manuals and user guides View all Stihl HL 100 K 0186 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Fueling Preparations Opening the filler cap English Adjusting the Cutter Bar 135° Version 2709BA003 KN N Before fueling, clean the filler cap and the area around it to ensure that no dirt falls into the tank. Always thoroughly shake the mixture in the canister before fueling your machine. N Position the machine so that the filler cap is facing up. WARNING In order to reduce the risk of fire and personal injury from escaping gas vapor and fumes, remove the fuel filler cap carefully so as to allow any pressure build-up in the tank to release slowly. 266BA028 KN N Turn the cap counterclockwise until it can be removed from the tank opening. N Remove the filler cap. Refueling Take care not to spill fuel while fueling and do not overfill the tank. Closing the filler cap N Position cap. N Turn the cap clockwise as far as it will go and tighten it as securely as possible by hand. 2709BA004 KN The angle of th cutter bar can be adjusted upwards in 4 stages from 0° (straight) to 45°, and downwards in 8 stages from 0° to 90° (right angle facing down). There are therefore 13 possible working positions. There is also a special transport position for the cutter bar. WARNING To reduce the risk of injury, carry out the adjustment only when the cutting blades are at a standstill - engine at idle speed. HL 100, HL 100 K 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
HL 100, HL 100 K
English
17
Preparations
N
Before fueling, clean the filler cap
and the area around it to ensure that
no dirt falls into the tank.
Always thoroughly shake the mixture in
the canister before fueling your
machine.
N
Position the machine so that the
filler cap is facing up.
WARNING
In order to reduce the risk of fire and
personal injury from escaping gas vapor
and fumes, remove the fuel filler cap
carefully so as to allow any pressure
build-up in the tank to release slowly.
Opening the filler cap
N
Turn the cap counterclockwise until
it can be removed from the tank
opening.
N
Remove the filler cap.
Refueling
Take care not to spill fuel while fueling
and do not overfill the tank.
Closing the filler cap
N
Position cap.
N
Turn the cap clockwise as far as it
will go and tighten it as securely as
possible by hand.
135° Version
The angle of th cutter bar can be
adjusted upwards in 4 stages from 0°
(straight) to 45°, and downwards in 8
stages from 0° to 90° (right angle facing
down). There are therefore 13 possible
working positions.
There is also a special transport position
for the cutter bar.
WARNING
To reduce the risk of injury
, carry out the
adjustment only when the cutting blades
are at a standstill – engine at idle speed.
Fueling
266BA028 KN
2709BA003 KN
2709BA004 KN
Adjusting the Cutter Bar