Sony ECM-S1 Help Guide - Page 30

mute lamp Microphone, Indicator lamps Microphone

Get Sony ECM-S1 PDF manuals and user guides View all Sony ECM-S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Microphone (Lit in blue)*2 The receiver is turned off. Receiver ‐ (Unlit) Microphone Blinking slowly in blue (on standby))*1 *2 The microphone is turned off. Receiver ‐ (Unlit (on standby))*1 Microphone ‐ (Unlit) Audio is interrupted due to bad communication conditions. Receiver (Blinking in blue (The faster the blinking speed, the worse the communication conditions.))*3 Microphone (Blinking in blue (The faster the blinking speed, the worse the communication conditions.))*2 *3 The built-in battery is charging. ‐ (Unlit) *1 When the lamp stays in this state for 5 minutes, the auto power-off function of this unit is activated. Turn off this unit, and then turn it back on. *2 When a wired connection is made with the microphone for audio recording, the LINK lamp stays unlit. *3 Check the LINK lamps on the receiver and the microphone for the communication state. Due to some surrounding factors, including poor radio conditions and a high number of obstacles between the receiver and the microphone, the communication state between the two devices may deteriorate, causing audio interruptions or noises. If this is the case, the LINK lamps blink in blue. Make sure that the two devices are located appropriately apart from each other, there are no obstacles between them, and the LINK lamps are steadily lit in blue before you use the receiver and the microphone. (mute) lamp (Microphone) The microphone is not in mute mode. ‐ (Unlit) The microphone is in mute mode. (Lit in red) Indicator lamps (Microphone) Level meter mode Default indication. The number of lit indicator lamps varies according to the recording volume level. Adjust the recording volume level by turning the AUDIO LEVEL dial while monitoring the indicator lamps, or adjust the distance between the audio source and the microphone. In the event that sounds are picked at the normal volume level: Adjust the recording volume level so that none of the indicator lamps would light in orange. In the event that sounds are picked at an extremely loud volume level: Adjust the recording volume level so that the top indicator lamp would not light in red. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
Microphone
(Lit in blue)
*2
The receiver is turned off.
Receiver
-
(Unlit)
Microphone
-
-
-
-
(Blinking slowly in blue (on standby))
*1
*2
The microphone is turned off.
Receiver
-
(Unlit (on standby))
*1
Microphone
-
(Unlit)
Audio is interrupted due to bad communication conditions.
Receiver
(Blinking in blue (The faster the blinking speed, the worse the communication conditions.))
*3
Microphone
(Blinking in blue (The faster the blinking speed, the worse the communication conditions.))
*2
*3
The built-in battery is charging.
-
(Unlit)
(mute) lamp (Microphone)
The microphone is not in mute mode.
-
(Unlit)
The microphone is in mute mode.
(Lit in red)
Indicator lamps (Microphone)
Level meter mode
Default indication. The number of lit indicator lamps varies according to the recording volume level.
Adjust the recording volume level by turning the AUDIO LEVEL dial while monitoring the indicator lamps, or adjust
the distance between the audio source and the microphone.
In the event that sounds are picked at the normal volume level: Adjust the recording volume level so that none of
the indicator lamps would light in orange.
In the event that sounds are picked at an extremely loud volume level: Adjust the recording volume level so that
the top indicator lamp would not light in red.
When the lamp stays in this state for 5 minutes, the auto power-off function of this unit is activated. Turn off this unit, and then turn it back on.
*1
When a wired connection is made with the microphone for audio recording, the LINK lamp stays unlit.
*2
Check the LINK lamps on the receiver and the microphone for the communication state.
Due to some surrounding factors, including poor radio conditions and a high number of obstacles between the receiver and the microphone, the
communication state between the two devices may deteriorate, causing audio interruptions or noises. If this is the case, the LINK lamps blink in
blue. Make sure that the two devices are located appropriately apart from each other, there are no obstacles between them, and the LINK lamps
are steadily lit in blue before you use the receiver and the microphone.
*3
30