Sony ECM-S1 Help Guide - Page 22

Make sure that the LINK lamp on the receiver is lit in blue, and then start recording.

Get Sony ECM-S1 PDF manuals and user guides View all Sony ECM-S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Immediately after the receiver and the microphone are turned on, the LINK lamp on the microphone starts blinking slowly in blue. This indicates that each of the devices is making a series of attempts to detect, connect to, and authenticate the other device. When a connection is established between the devices and clear audio recording is possible, the LINK lamps on both devices stay lit in blue. If no connection is established, bring the microphone and the receiver closer to each other for another attempt. The devices may be under influence of environmental or other factors. 3 Make sure that the LINK lamp on the receiver is lit in blue, and then start recording. Before recording, make sure that the surface of the microphone with the (power) button faces to the sound source. Adjust the recording volume level by turning the AUDIO LEVEL dial while monitoring the indicator lamps, or adjust the distance between the audio source and the microphone. In the event that sounds are picked at the normal volume level: Adjust the recording volume level so that none of the indicator lamps would light in orange. In the event that sounds are picked at an extremely loud volume level: Adjust the recording volume level so that the top indicator lamp would not light in red. Note When you are finished with using the receiver and the microphone, select "OFF" with the slide switch on the receiver and press and hold the (power) button on the microphone for about 2 seconds to turn off this unit. Depending on the using condition, noises may be included in audio recordings. When a radio device is nearby, keep this unit sufficiently away from the device. While audio recording is in progress, operating the filter switch, the directivity selection switch, or the AUDIO LEVEL dial on the microphone may cause operation sounds to be included in the recording. Before changing the switch/dial settings, be sure to stop the recording. When an audio recording is made with this unit, an operation sound (an electronic sound) may be included at the beginning of the recording. It is recommended that you disable the operation sound settings on your computer or smartphone before making audio 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
Note
When you are finished with using the receiver and the microphone, select “OFF” with the slide switch on the receiver and press
and hold the
(power) button on the microphone for about 2 seconds to turn off this unit.
Depending on the using condition, noises may be included in audio recordings.
When a radio device is nearby, keep this unit sufficiently away from the device.
While audio recording is in progress, operating the filter switch, the directivity selection switch, or the AUDIO LEVEL dial on the
microphone may cause operation sounds to be included in the recording. Before changing the switch/dial settings, be sure to
stop the recording.
When an audio recording is made with this unit, an operation sound (an electronic sound) may be included at the beginning of the
recording. It is recommended that you disable the operation sound settings on your computer or smartphone before making audio
Immediately after the receiver and the microphone are turned on, the LINK lamp on the microphone starts blinking
slowly in blue. This indicates that each of the devices is making a series of attempts to detect, connect to, and
authenticate the other device. When a connection is established between the devices and clear audio recording is
possible, the LINK lamps on both devices stay lit in blue.
If no connection is established, bring the microphone and the receiver closer to each other for another attempt. The
devices may be under influence of environmental or other factors.
Make sure that the LINK lamp on the receiver is lit in blue, and then start recording.
Before recording, make sure that the surface of the microphone with the
(power) button faces to the sound
source.
Adjust the recording volume level by turning the AUDIO LEVEL dial while monitoring the indicator lamps, or adjust
the distance between the audio source and the microphone.
In the event that sounds are picked at the normal volume level: Adjust the recording volume level so that none
of the indicator lamps would light in orange.
In the event that sounds are picked at an extremely loud volume level: Adjust the recording volume level so that
the top indicator lamp would not light in red.
3
22