Sharp XV-Z12000 XV-Z12000 Operation Manual - Page 35

Image Projection - lamp reset

Get Sharp XV-Z12000 - SharpVision - DLP Projector PDF manuals and user guides View all Sharp XV-Z12000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 36. 1 Plug the power cord into the wall outlet. • The power indicator illuminates red, and the projector enters standby mode. 2 Press on the remote control or on the projector. • The power indicator illuminates blue. After the lamp indicator illuminates, the projector is ready to start operation. ", ',\, | buttons ENTER button Note • The lamp indicator illuminates, indicating the status of the lamp. Blue: The lamp is ready. Blue blinking: The lamp is warming up. Red: The lamp should be replaced. •If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take some time to illuminate. • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. STANDBY button ENTER button Power indicator Lamp indicator MENU button INPUT button STANDBY button ON button ON button MENU button ", ', \, | buttons INPUT buttons -34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
36
.
1
Plug the power cord into the
wall outlet.
•
The power indicator illuminates red, and
the projector enters standby mode.
2
Press
on the remote control
or
on the projector.
•
The power indicator illuminates blue.
After the lamp indicator illuminates, the
projector is ready to start operation.
Note
•
The lamp indicator illuminates, indi-
cating the status of the lamp.
Blue:
The lamp is ready.
Blue blinking:
The lamp is
warming up.
Red:
The lamp should be replaced.
•
If the projector is put into the
standby mode and immediately
turned on again, the lamp indicator
may take some time to illuminate.
•
When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
-34
INPUT
button
ON button
STANDBY
button
MENU button
"
,
'
,
\
,
|
buttons
ENTER
button
ON button
INPUT
buttons
"
,
'
,
\
,
|
buttons
MENU button
ENTER
button
STANDBY
button
Lamp indicator
Power indicator