Sharp XG-P560W-N XG-P560W Operation Manual - Page 75

Remove the lamp unit., Insert the new lamp unit., Replace the lamp unit cover.

Get Sharp XG-P560W-N - WXGA DLP Projector PDF manuals and user guides View all Sharp XG-P560W-N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Securing screws 3 Remove the lamp unit. • Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. 4 Insert the new lamp unit. • Fully insert the lamp unit into the lamp unit compartment. Press the handles back to their positions, and tighten the securing screws. 5 Replace the lamp unit cover. • Slide the lamp unit cover to the position where the indicator "|" of the lamp cover unit and the "\" of the projector will meet to close the cover. Then tighten the user service screw to secure the lamp unit cover. Info • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Handle Compartment for Lamp 1 Compartment for Lamp 2 AN-P610LP Appendix User service screw -73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Appendix
-73
3
Remove the lamp unit.
•
Loosen the securing screws (two for
each lamp) from the lamp unit. Hold the
lamp unit by the handle and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
4
Insert the new lamp unit.
•
Fully insert the lamp unit into the lamp
unit compartment. Press the handles
back to their positions, and tighten the
securing screws.
5
Replace the lamp unit cover.
•
Slide the lamp unit cover to the position
where the indicator “
|
” of the lamp cover
unit and the “
\
” of the projector will meet
to close the cover. Then tighten the user
service screw to secure the lamp unit
cover.
Info
•
If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
Securing screws
Handle
AN-P610LP
Compartment
for
Lamp 1
Compartment
for
Lamp 2
User service screw