Sharp R-351NW Service Manual - Page 8

General Information

Get Sharp R-351NW PDF manuals and user guides View all Sharp R-351NW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

R-351NW CHAPTER 5. GENERAL INFORMATION [1] GROUNDING INSTRUCTIONS This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. WARNING: Improper use of the grounding plug can result in a risk of electric shock. Electrical Requirements The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical supply. It is recommended that a separate circuit serving only this appliance be provided. When installing this appliance, observe all applicable codes and ordinances. A short powersupply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Where a two-pronged wall-receptacle is encountered, it is the personal responsibility and obligation of the customer to contact a qualified electrician and have it replaced with a properly grounded three-pronged wall receptacle or have a grounding adapter properly grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp. or higher rated cord. Do not drape over a countertop or table where it can be pulled on by children or tripped over accidentally. Grounded Receptacle Box 3-Pronged Plug Grounding Pin 3-Pronged Receptacle CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND GROUNDING PRONG FROM THIS PLUG. [2] OVEN DIAGRAM 1. OVEN 1. Door open button 5 Push to open door. 2. Oven door with see-through window 13 14 3. Safety door latches The oven will not operate unless the 4 6 12 door is securely closed. 4. Door hinges 1 5. Door seals and sealing surfaces 6. Turntable motor shaft 3 2 7. Removable turntable support 8 11 10 3 7 Carefully place the turntable support 9 in the center of the oven floor. 8. Removable turntable Place the turntable securely on the turntable support. The turntable will rotate clockwise or counterclockwise. Only remove for cleaning. 9. Ventilation openings (Rear) 10. Oven light It will light when oven is operating or when the door is open. 11. Waveguide cover: DO NOT REMOVE. 12. Auto-Touch control panel 13. Time display: 99 minutes, 99 seconds 14. Power supply cord 5 - 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
R-351NW
[2] OVEN DIAGRAM
1. OVEN
1.
Door open button
Push to open door.
2.
Oven door with see-through window
3.
Safety door latches
The oven will not operate unless the
door is securely closed.
4.
Door hinges
5.
Door seals and sealing surfaces
6.
Turntable motor shaft
7.
Removable turntable support
Carefully place the turntable support
in the center of the oven
fl
oor.
8.
Removable turntable
Place the turntable securely on the turntable support. The turntable will rotate clockwise or counterclockwise. Only remove for
cleaning.
9.
Ventilation openings (Rear)
10. Oven light
It will light when oven is operating or when the door is open.
11. Waveguide cover: DO NOT REMOVE.
12. Auto-Touch control panel
13. Time display: 99 minutes, 99 seconds
14. Power supply cord
14
8
9
7
12
13
1
5
3
2
4
6
11
3
10
5 - 1
CHAPTER 5. GENERAL INFORMATION
[1] GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric
current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15 or 20 amp. fused electrical
supply. It is recommended that a separate circuit serving only this appliance be provided.
When installing this appliance, observe all applicable codes and ordinances. A short power-
supply cord is provided to reduce risks of becoming entangled in or tripping over a longer
cord. Where a two-pronged wall-receptacle is encountered, it is the personal responsibility
and obligation of the customer to contact a quali
fi
ed electrician and have it replaced with
a properly grounded three-pronged wall receptacle or have a grounding adapter properly
grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp.
or higher rated cord. Do not drape over a countertop or table where it can be pulled on by
children or tripped over accidentally.
CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE ROUND
GROUNDING PRONG FROM THIS PLUG.
3-Pronged
Plug
Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle