Sharp PN-R606 PN-R Series Operation Manual - Page 58

Specifications nProduct Specifications Model PN-R706 PN-R606 LCD component 70" Class 60" Class [69-1/2 inch (176.56 cm) diagonal] [60-1/16 inch (152.60 cm) diagonal] TFT LCD TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors Approx. 16.77 million colors Pixel pitch Max. brightness (typical) 0.802 mm (H) × 0.802 mm (V) 700 cd/m2 *1 0.692 mm (H) × 0.692 mm (V) Contrast ratio (typical) 5000: 1 Viewing angle 176° right/left/up/down (contrast ratio ≥ 10) Screen active area inch (mm) 60-9/16 (W) x 34-1/16 (H) (1538.88 x 865.62) 52-5/16 (W) x 29-7/16 (H) (1329.12 x 747.63) Computer input signal Sync signal Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω], DisplayPort 1.2, HDMI Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*2, Composite sync (TTL: positive/negative)*2 Plug and play VESA DDC2B Power management VESA DPMS, DVI DMPM Input terminals Video HDMI x 2 DVI-D 24 pin (HDCP compatible) x 1 Mini D-sub 15 pin, 3 rows x 1 DisplayPort x 1 Audio 3.5 mm mini stereo jack x 1 Serial (RS-232C) D-sub 9 pin x 1 Output terminals Video DisplayPort x 1 Audio 3.5 mm mini stereo jack x 1 Serial (RS-232C) D-sub 9 pin x 1 LAN terminal 10 BASE-T/100 BASE-TX Power supply terminal 5 V, 2 A (5 V, 500 mA when the expansion slot is used) (USB Type-A connector) Expansion slot 12 V, 2.4 A (power supplied when expanding the functions with an optional part) Speaker output 10 W + 10 W Power requirement AC 100 - 240 V, 2.6 A, 50/60 Hz AC 100 - 240 V, 2.2 A, 50/60 Hz Operating temperature *3 32°F to 104°F (0°C to 40°C) Operating humidity 20% to 80% (no condensation) Power consumption (Input signal waiting mode *4 / standby mode *5) 230 W (2.5 W / 0.8 W) 190 W (2.5 W/0.8 W) Dimensions (excluding protrusions) inch (mm) Approx. 62-3/16 (W) x 2-9/16 (D) x Approx. 53-1/4 (W) x 2-3/8 (D) x 36-1/8 (H) (1579 x 65 x 918) 30-5/8 (H) (1352 x 60 x 778) Weight lbs. (kg) Approx. 99.3 (45) Approx. 88.2 (40) *1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the equipment, it is not possible to precisely maintain a constant level of brightness. *2 D-Sub input terminal only. *3 When using the monitor laying flat on a surface (when the monitor is tilted more than 20 degrees upward or downward from the perpendicular in relation to a level surface), use the monitor at a temperature between 32°F (0°C) to 86°F (30°C). Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments. *4 When SUPPLY USB POWER is set to POWER ON ONLY and no optional part is attached. *5 When POWER SAVE MODE is set to OFF, SUPPLY USB POWER is set to POWER ON ONLY, and no optional part is attached. When POWER SAVE MODE is set to ON: 0.5 W As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. E 58