Sanyo FWBP706F Owners Manual - Page 45

PBC Push Button Configuration

Get Sanyo FWBP706F PDF manuals and user guides View all Sanyo FWBP706F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

CC Wireless connection If you connect this unit to a wireless network, select "Wireless" and set up necessary settings. Please make a note of your SSID (Service Set Identifier - Wireless Network Name) and its WEP* / WPA / WPA2 Key before proceeding with the setup. * "Auto" cannot be used when the security protocol is set to "WEP". Auto PBC (Push Button Configuration) You can set up a wireless connection quickly. ("PBC" is only available when your router supports it. For details, please refer to the user manual of your wireless router.) Please confirm your wireless router has a PBC* (Push Button Configuration) button. 1. Use [ ] to select "Setup" in the home menu, then press [OK]. 2. Use [ ] to select " ", then press [OK] 3. Use [ ] to select "Network", then press [OK]. 4. Use [ ] to select "Interface", then press [OK]. • If you would like to make a change in wireless settings, select "Wireless Setting". • After selecting "Wireless Setting", a confirmation screen will appear. Use [ ] to select "Yes", then press [OK]. After pressing [OK], move on to step 6. 5. Use [ ] to select "Wireless", then press [OK]. • When attempting to switch from "Ethernet" to "Wireless", a confirmation screen will appear. Use [ ] to select "Yes", then press [OK]. 6. Use [ ] to select "Auto", and use [ ] to select "Next", then press [OK]. 7. Use [ ] to select "PBC". Setup Network Language Streaming Co... Security System WPS(Wi-Fi Protected Setup) PBC PIN Please press Push Button on the Access Point within 120 seconds after you select the "Next" Button below. Refresh Previous Next 8. Push the PBC button* on your wireless router, then quickly select "Next" using [ ] and press [OK]. * PBC button may be called WPS (Wi-Fi Protected Setup) button on your wireless router. 9. "Connection success and IP is obtained." will be displayed. Press [OK] to complete the settings. DD Not "Auto" cannot be used when the security mode of your access point is set to "WEP". Please try either method below. • Connect the unit to the access point using "Scan" or "Manual" mode. • Change the access point's security mode from "WEP*" to "WPA" or "WPA2". * "WEP" is not recommended to be used due to its "Major security flaws". Change the security protocol on the wireless router to "WPA" or "WPA2 (recommended)" mode. (For access point configuration, please consult the user manual of your wireless router or manufacturer.) continued on next page EN 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
EN
45
C
Wireless connection
If you connect this unit to a wireless network, select “Wireless” and set up necessary settings.
Please make a note of your SSID (Service Set Identifier – Wireless Network Name) and its WEP* / WPA / WPA2
Key before proceeding with the setup.
* “Auto” cannot be used when the security protocol is set to “WEP”.
Auto
PBC (Push Button Configuration)
You can set up a wireless connection quickly.
(“PBC” is only available when your router supports it. For details, please refer to the user manual of your
wireless router.)
Please confirm your wireless router has a PBC* (Push Button Configuration) button.
1.
Use
[
]
to select “Setup” in the home menu, then press
[OK]
.
2.
Use
[
]
to select “
”, then press
[OK]
3.
Use
[
]
to select “Network”, then press
[OK]
.
4.
Use
[
]
to select “Interface”, then press
[OK]
.
•
If you would like to make a change in wireless settings, select “Wireless Setting”.
•
After selecting “Wireless Setting”, a confirmation screen will appear.
Use
[
]
to select “Yes”, then press
[OK]
. After pressing
[OK]
, move on to step 6.
5.
Use
[
]
to select “Wireless”, then press
[OK]
.
•
When attempting to switch from “Ethernet” to “Wireless”, a confirmation screen will appear.
Use
[
]
to select “Yes”, then press
[OK]
.
6.
Use
[
]
to select “Auto”, and use
[
]
to select “Next”, then press
[OK]
.
7.
Use
[
]
to select “PBC”.
Language
Streaming Co...
Security
System
Network
PBC
PIN
Please press Push Button on the Access Point within
120 seconds after you select the "Next" Button below.
WPS(Wi-Fi Protected Setup)
Previous
Refresh
Next
Setup
8.
Push the PBC button* on your wireless router, then quickly select “Next” using
[
]
and press
[OK]
.
* PBC button may be called WPS (Wi-Fi Protected Setup) button on your wireless router.
9.
“Connection success and IP is obtained.” will be displayed. Press
[OK]
to complete the settings.
Note
D
“Auto” cannot be used when the security mode of your access point is set to “WEP”.
Please try either method below.
•
Connect the unit to the access point using “Scan” or “Manual” mode.
•
Change the access point’s security mode from “WEP*” to “WPA” or “WPA2”.
*
“WEP” is not recommended to be used due to its “Major security flaws”. Change the security protocol on
the wireless router to “WPA” or “WPA2 (recommended)” mode.
(For access point configuration, please consult the user manual of your wireless router or manufacturer.)
continued on next page