Metabo W 24-230 MVT Operating Instructions 2 - Page 18
Troubleshooting, Accessories, Repairs, Environmental Protection
![]() |
View all Metabo W 24-230 MVT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
en ENGLISH using a vacuum cleaner or by blowing in dry air. Prior to this operation, separate the power tool from the power source and wear protective glasses and dust mask. Button (9) for adjusting the handle: Occasionally blow compressed air through the button (when pressed, in all 3 main handle positions). Prior to this operation, separate the power tool from the power source and wear protective glasses and dust mask. 10. Troubleshooting Machine with "WE..." in the model designation: - Overload protection: The electronic signal display (6) lights up and the load speed decreases dramatically. The motor temperature is too high! Run the machine in idling until it cools down and the electronic signal display switches off. - Overload protection: The electronic signal display (6) lights up and the load speed decreases slightly. The machine is overloaded. Work with a reduced load until the electronic signal display goes out. - Electronic safety stop: The electronic signal display (6) lights up and the machine was SWITCHED OFF automatically. If the slew rate of the current is too high (for example, if the machine suddenly seizes or kickback occurs), the machine switches off. Switch off the machine at the trigger switch (8). Switch it on again and continue to work as normal. Try to prevent the machine from seizing. See Section 4.2. - Restart protection: The electronic signal display (6) FLASHES and the machine does not start. The restart protection is active. If the mains plug is inserted with the machine switched on, or if the power supply is restored following an interruption, the machine does not start up. Switch the machine off and on again. - When switched on, the machine accelerates to maximum speed very quickly, i.e. automatic restriction of the starting current does not work (soft start). An electronic error exists. Other safety-related electronic functions are no longer available. Have the machine repaired immediately (see 12.). W 22-180 MVT, W 22-230 MVT, W 24-180 MVT, W 24-230 MVT, W 26-180 MVT, W 26-230 MVT: - Switching on the machine reduces the voltage briefly. Unfavourable mains power conditions may have a detrimental effect on other machines. Power impedances less than 0.2 ohm should not cause malfunctions. 11. Accessories Use only genuine Metabo accessories. Use only accessories which fulfil the requirements and specifications listed in these operating instructions. Fit accessories securely. Secure the machine if it is operated in a bracket. Loss of control can cause personal injury. 18 See page 4. A Roughing disc (always use with safety guard attached) B Lamellar grinding disc (always use with safety guard attached) C Parting safety guard. D Parting disc (always use with parting safety guard attached) E Diamond discs (always use with safety guard or parting safety guard attached) F Parting safety guard with guide slot (place on machine and secure with screws.) (with adapter for connection to a suitable dust extractor for extraction of stone dust generated when cutting stone slabs.) G Hand guard (for attaching under the additional side-mounted handle.) H Extension piece (for working with supporting discs. Increases the distance between the spindle and the supporting disc by approx. 35 mm) I Supporting disc for fibre discs (always attach using the supporting disc clamping nut supplied.) (always use with the hand guard attached.) J Fibre discs (always use with the hand guard attached.) K Steel wire brushes (always use with the hand guard attached.) L Bench cut-off stand M Adjusting nut (13) N "Quick" clamping nut (1) For the complete range of accessories, see www.metabo.com or the main catalogue. 12. Repairs Repairs to electrical tools must be carried out by qualified electricians ONLY! Contact your local Metabo representative if you have Metabo power tools requiring repairs. For addresses see www.metabo.com. You can download a list of spare parts from www.metabo.com. 13. Environmental Protection The generated grinding dust may contain harmful substances. Dispose appropriately. Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories. Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Directive 2002/ 96/EC on waste electrical and electronic equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling.
![](/manual_guide/products/metabo-w-24180-mvt-operating-instructions-2-2340f63/18.png)