Metabo T 13-125 Operating Instructions - Page 11

5.2 Attaching the additional handle Always work with the additional handle (2) attached! - Remove side handle (2) from the angle grinder and screw in firmly on the left or right side of the extraction guard (12). 5.3 Attaching the dust extraction Always use a suitable dust extraction system: Connect an M-class vacuum cleaner to the extractor connection (5) piece. For optimal dust extraction, use the connecting sleeve 6.30796. We recommend using an antistatic suction hose Ø 35 mm. 6. Attaching the accessory Prior to any conversion work: Pull the mains plug from the socket. The machine must be switched off and the spindle at a standstill. 6.1 Attaching the diamond cutting disc Dismantle the extraction guard (12) and base part (11) See page 2, fig. A. 1. Push slider (10) in the direction of the arrow and tilt extraction guard (12) as shown in the direction of the arrow. 2. The extraction guard (12) can be removed from the base part (11) in the shown position. Attach the diamond cutting disc at the angle grinder. 3. Press in the spindle locking button (4) and turn the spindle (20) until the spindle locking button engages noticeably. 4. Fit the support flange (19) (scope of delivery of the angle grinder) on the spindle. The flange should not turn on the locked spindle when properly attached. 5. Fit the spacer sleeve (18) on the support flange (19). 6. Put the diamond cutting disc (17) on the spacer sleeve (18). Make sure the direction of rotation is correct. The direction of rotation is indicated by arrows on the saw blade and extraction guard. 7. Ensure that the clamping nut with two holes (16) and the spindle (20) of the angle grinder match: Lettering on the clamping nut with two holes and thread size on the angle grinder's rating plate have to match (M14 / 5/8"). 8. Screw on two-hole adjustment nut (16). 9. Push spindle locking button (4) and keep pressed. 10.Firmly tighten the two-hole adjustment nut (16) using a two-hole spanner (15). Assemble extraction guard (12) and base part (11) 11.See page 2, fig. B. Insert the 2 bolts of the extraction hood (12) as shown in theguides of the base part (11). ENGLISH en 12.Swivel the extraction guard (12) and base part (11) into each other until the slider (10) engages and both parts are connected to each other. 13.Check for secure connection. 7. Use Always hold the tool by the main handle and side handle (2) , using both hands. 1. Set required cutting depth: Loosen the clamping screw (6) and set the required cutting depth at the scale, tighten clamping screw (6) again. 2. Place the guard with the base part (11) on the workpiece. 3. Switch on machine and wait until the full speed has been reached. 4. Turn the locking lever (3). Slowly guide the machine downwards to the stop: the diamond cutting disc penetrates deeply into the material. 5. Pull/push machine only in direction of the arrow (1) (work in reverse rotation). Otherwise there is the danger of the machine kicking back from the cut out of control. Guide the machine evenly at a speed suitable for the material being processed. 6. Once the channel is complete, switch off the tool and hold it steady until the diamond cutting disc comes to a stop. Never attempt to remove the cutting disc from the cut while the wheel is in motion otherwise kickback may occur. 7. Guide the machine upwards until the stop: the locking lever (3) engages. 8. Put machine aside. Note: For special applications, the guard can also be used without base part (11). The removal and fitting of the base part is described in chapter 6.1. 8. Maintenance Prior to each use, check if there are parts missing, worn, broken, torn or damaged. Do not use defective or incomplete guard. 9. Accessories Use only genuine Metabo accessories. Use only accessories which fulfil the requirements and specifications listed in these operating instructions. CED 125 Plus is suitable for work with the Metabo guide rail (6.31213). The maximum permitted thickness of the diamond cutting disc is 3 mm (1/8"). Before initial use: - Loosen the screw of the guide rail adapter (8). - Place the machine on the guide rail 6.31213. - Move the guide rail adapter and adjust the play. - Tighten the screws of the guide rail adapter again (8). For a complete range of accessories, see www.metabo.com or the catalogue. 11