Marantz SR8015 Sound Mode Table - Page 3

Before Servicing This Unit Electrical Sound modes and surround parameters Surround Parameter Sound mode Cinema EQ Loudness Management ※2 Dynamic Compression ※3 Dialog Control ※4 Low Frequency Effects ※5 Speaker Select ※6 Speaker Virtualizer ※7 DTS Neural:X IMAX IMAX Audio Settings High Pass Filter ※8 Low Pass Filter ※8 Subwoofer Mode ※8 Auro-Matic Auro-Matic 3D Preset 3D Strength Auro-3D Mode Dialog Subwoofer Enhancer Tone ※9 Direct/Pure Direct (2-channel) ※ 1 ○ ○ ○※ 18 Direct/Pure Direct (Multi-channel) ※1 ○ ○ ○ ○ DSD Direct (2-channel) ○※ 18 DSD Direct (Multi-channel) Stereo ○ ○ ○ ○ ○※ 19 ○ ○ Dolby Atmos ○ ○ ○ ○ ○ ○ ○ Dolby TrueHD ○ ○ ○ ○ ○ ○ Dolby Digital Plus ○ ○ ○ ○ ○ ○ Dolby Digital ○ ○ ○ ○ ○ ○ Dolby Surround ○ ○ ○ ○ ○ ○ IMAX DTS:X ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ IMAX DTS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ DTS:X ○ ○ ○ ○ ○ ○ ○ ○ DTS-HD ○ ○ ○ ○ ○ ○ DTS Express ○ ○ ○ ○ ○ DTS 96/24 ○ ○ ○ ○ ○ DTS Surround ○ ○ ○ ○ ○ ○ DTS Neural:X ○ ○ ○ ○ ○ DTS Virtual:X ○ ○ ○ ○ Auro-3D ○ ○ ○※ 20 ○※ 20 ○※ 21 ○ ○ Auro-2D Surround ○ ○ ○ ○ Multi Ch In ○ ○ ○ ○ MPEG-4 AAC (JP Only) ○ ○ ○ ○ MPEG-2 AAC (JP Only) ○ ○ ○ ○ Multi Ch Stereo ○ ○ ○ ○ ○ ○ ○ ○ Virtual ○ ○ ○ ○ ○ ※ 1 During playback in Pure Direct mode, the surround parameters are the same as in Direct mode. ※ 2 This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played. ※ 3 This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X or DTS signal is played. ※ 4 This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input. ※ 5 This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played. ※ 6 This item can be selected when Height, Ceiling or Dolby Atmos Enabled speakers are used. ※ 7 This item can be set when any Height, Ceiling or Dolby Atmos Enabled speakers are not used, or Surround speakers are not used. ※ 8 This item can be selected when "IMAX Audio Settings" in the menu is set to "Manual". ※ 9 This item cannot be set when "Dynamic EQ" is set to "On". ※ 10 This item cannot be set when "Center" is set to "None". ※ 11 This item cannot be set when "Subwoofer" in the menu is set to "None". ※ 12 This item cannot be set when Audyssey® Setup (Speaker Calibration) has not been performed. ※ 13 This item cannot be selected when a DTS:X format with a sampling frequency of over 48 kHz is input. ※ 14 This item cannot be set when "MultEQ® XT32" in the menu is set to "Off". ※ 15 This item cannot be set when sound mode is "DTS Virtual:X" or sound mode that have "+Virtual:X" in the sound mode name. ※ 16 This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz. ※ 17 This can be set when the LFE signal is included in the input signal. ※ 18 This setting is available when "Subwoofer Mode" in the menu is set to "LFE+Main". ※ 19 This item can be set when "Front" is set to "Small" or "Subwoofer Mode" is set to "LFE+Main". ※ 20 This can be set if the input signal does not contain an Auro-3D signal or if the input Auro-3D signal does not contain Front Height channels. ※ 21 This can be set if the input signal contains an Auro-3D signal. Audyssey Subwoofer Level Adjust ※ 11 MultEQ® XT32 ※ 12 ※ 13 Dynamic EQ ※ 14 ※ 15 Dynamic Volume ※ 14 ※ 15 Audyssey LFC™ ※ 14 ※ 15 M-DAX ※ 16 ○※ 18 ○ ○※ 18 ○ ○※ 19 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Bass Sync ※ 17 ○ Mechanical Repair Information Updating 8