LiftMaster TDC LiftMaster MAXUM Commercial Door Operator Overview - English - Page 25

Quick Connect Guide

Get LiftMaster TDC PDF manuals and user guides View all LiftMaster TDC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Quick Connect Guide MAXUM Commercial Door Operators Wi-Fi® Provisioning • Step 1 Things You Will Need for a Quick and Easy Connection • Smart Wi-Fi enabled device (phone, tablet, computer) • 2.4 Ghz Wi-Fi Network and Name (SSID) • Wi-Fi password • myQ device Serial Number (located on operator) • 3+ Bars of Wi-Fi signal strength at operator installation location. (verify with pre-connected mobile device) At Operator 1. Press and hold the and on the wall control for 3+ seconds. (Password for System Settings is 326). 2. Once door specifics are confirmed and open/close limits are set, choose "YES" for Learn Wi-Fi. Note: Wi-Fi learn mode will timeout after 10 minutes. At Smart Device (Phone, Computer, etc.) 3. Go to Wi-Fi settings and check available networks to find myQ - ### (NOTE: #'s match the last 3 digits of the Operator's Serial Number) 4. Select connect. If connected successfully: "Connected, no internet" is displayed. 5. Navigate to setup.myqdevice.com. 6. Select your 2.4 Ghz preferred network name (SSID). 7. Enter password then select "Next". 8. To continue with setup, tap "Yes" when asked if you have heard 3 beeps. (Note: even if you don't hear them, press yes to continue.) 9. Select "Next" then verify the Operator LCD screen displays "Wi-Fi Learned". 10. myQ Serial Number will be displayed. Save the myQ Serial Number for reference. 11. Once the Wi-Fi is learned, exit the "Learn Window" screen by pressing and holding and on the Wall Control. Congratulations! Your operator should now be on local Wi-Fi and ready to receive over-the-air firmware updates. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Quick Connect Guide
MAXUM
Commercial Door Operators
Wi-Fi® Provisioning • Step 1
Things You Will Need for a Quick and Easy Connection
• Smart Wi-Fi enabled device (phone, tablet, computer)
• 2.4 Ghz Wi-Fi Network and Name (SSID)
• Wi-Fi password
• myQ device Serial Number (located on operator)
• 3+ Bars
of Wi-Fi signal strength at operator installation
location. (verify with pre-connected mobile device)
At Operator
1.
Press and hold the
and
on the wall control
for 3+ seconds. (Password for System Settings is 326).
2.
Once door specifics are confirmed and open/close limits
are set, choose “YES” for Learn Wi-Fi.
Note: Wi-Fi learn mode will timeout after 10 minutes.
3.
Go to Wi-Fi settings and check available networks to find
myQ - ### (NOTE: #’s match the last 3 digits of the
Operator’s Serial Number)
4.
Select connect. If connected successfully:
“Connected, no internet” is displayed.
5.
Navigate to setup.myqdevice.com.
6.
Select your 2.4 Ghz preferred network name (SSID).
7.
Enter password then select “Next”.
8.
To continue with setup, tap “Yes” when asked if you have heard 3 beeps.
(Note: even if you don’t hear them, press yes to continue.)
9.
Select “Next” then verify the Operator LCD screen displays
“Wi-Fi Learned”.
10.
myQ Serial Number will be displayed.
Save the myQ Serial Number for reference.
11
. Once the Wi-Fi is learned, exit the “Learn Window” screen
by pressing and holding
and
on the Wall Control.
Congratulations! Your operator should now be on
local Wi-Fi and ready to receive over-the-air firmware updates.
At Smart Device (Phone, Computer, etc.)
23