LiftMaster LMSC1000 Installation Manual - English French Spanish
LiftMaster LMSC1000 Manual
View all LiftMaster LMSC1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster LMSC1000 manual content summary:
- LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 1
3RX, 3SX, 4X OR 6P. Supported LiftMaster RFID tags (Order Separately) Reader Specifications Part Number FCC ID Dimensions Polarization Frequency range Supported Protocol Read Range Anti-Collision Environment Connectivity RF Output Power Weight Protocol Firmware LMSC1000 input rating UL 294 Levels - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 2
generates and emits Radio Frequency (RF) energy which may cause interference with access control receivers. Avoid aligning the LMSC1000 read field within close proximity of any other receiving device antenna. Correct Passenger Side Reader Placement Reader Mounting Step 1: Install mounting bracket - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 3
) +12V DC Power Supply Index Color Solid Black Black w/Dash Function +12V DC - 12V DC (GND) Reader LEDs The LEDs on the front of the LMSC1000 Reader will illuminate red when powered. Blinking blue LEDs indicate an RFID tag is being read. Dry Contact Relay Output For applications where RFID tag - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 4
Reader Wiring Diagram Power Transformer LMSC1000 RFID Reader The gray, blue, and brown wires from the RFID Reader are unused. Solid Black Black w/Dash Red Black Green White Yellow White Green - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 5
PWR SET LP SET/ERR SER I SER 0 WO DC SETUP 6 LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Dry Cont Beeper Enable/Disable By default, the LMSC1000 will beep when it reads an RFID tag. To toggle this feature (turn on or off) perform the following steps: 1. Place the module in - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 6
LiftMaster tags into myQ® Business™ When adding a new credential in myQ® Business™, go to the credentials tab, click "Add new credentials" and when selecting type, choose RFID_Tags_LiftMaster. Troubleshooting Problem mounted Consult the RFID tag installation manual and make sure that the tags are - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 7
) using by the RFID reader. This is adjustable and a delay can be programmed the steps in the installation manual. to minimize the Wiegand outputs sent to the controller. Service Parts Part Mounting Bracket Wiegand Interface Module RF Power Supply - 3 amps Part Number K-AUMB RFID Bracket K-S2W - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 8
One Year Limited Warranty LiftMaster warrants to the first consumer purchaser of this product that it is radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 9
LiftMaster ne peuvent être utilisées qu'avec le lecteur de marque LiftMaster. CONTENU DE LA BOÎTE Support de Montage Boulons en U (2) Lecteur RFID LMSC1000 (20 à 30 pi) (selon l'étiquette) Jusqu'à 100 étiquettes/seconde Température de service : - 20 C à + 50 C Température d'entreposage : - 20 C à - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 10
LMSC1000 à grande proximité de l'antenne d'un autre dispositif de réception. Montage du lecteur Installer le support de montage à l'emplacement de montage désiré. Fixer le côté rond du support à la norme UL 325. Boucle de mise en service REMARQUE : Les exemples illustrés sont des recommandations - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 11
d'interface Wiegand Les instructions suivantes correspondent aux dispositions des connexions de câblage sur le système de lecteur LMSC1000. • Prendre des de 30 m (98,5 pi). Entrée de boucle de mise en service (facultative) Dans les applications où de multiples lecteurs RFID se trouveront à proximit - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 12
Transformateur de puissance Noir uni Noir avec pointillé Lecteur RFID LMSC1000 Rouge Noir Verte Blanc Jaune Les fils gris, bleu Alimentation (Allumé en continu lorsqu'une alimentation est présente) Boucle de mise en service (Allumé en continu lorsque la boucle est active) Erreur de données reçue - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 13
SER 0 WO DC SETUP 6 LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Dry Cont Activation/désactivation de l'avertisseur Par défaut, le lecteur LMSC1000 émettra des bips lorsqu'il lit une étiquette RFID. Pour faire basculer cette fonction (l'activer ou la désactiver), effectuer les étapes - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 14
de vos étiquettes LiftMaster dans myQ® active. Vérifier le réglage de la boucle de mise en service du module d'interface Wiegand sur le commutateur DIP S1-5 et s'assurer que en marche après l'avoir éteint et rallumé et que les instructions de dépannage ci-dessus ne révèlent pas le problème, celui - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 15
ES 1 et COM, de même qu'entre le câble de DONNÉES 0 et COM. La lecture de service normale devrait être d'au moins 4,9 à 5 V c. c. Une lecture inférieure à cette tension indique une Pièces de réparation Pièce Support de montage Module d'interface Wiegand Source d'alimentation RF - 3 A Numéro de piè - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 16
Garantie limitée de 1 an LiftMaster garantit à l'acheteur initial de ce produit que celui-ci des fréquences radio et, s'il n'est pas installé et utilisé conformément aux instructions, peut causer un brouillage nuisible aux communications radio. Cependant, rien ne garantit l'absence de brouillage - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 17
identificación por radiofrecuencia (RFID) de gran alcance LiftMaster • Modelo LMSC1000 El lector patentado de gran alcance y las etiquetas de vehículos LiftMaster le brindan un acceso rápido y fácil a su portón. El lector y las etiquetas de vehículos LiftMaster se deben usar como un sistema para que - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 18
emite energía de radiofrecuencia (RF) que puede generar interferencias con los receptores de control de acceso. Evite alinear el campo de lectura del LMSC1000 en proximidad de cualquier otra antena de dispositivo receptor. Montaje del lector Paso 1: Instale la ménsula de montaje en la ubicación de - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 19
de la alimentación de energía Color Negro Negro c/rayas Función +12 Vcc -12 VCC (TIERRA) LED del lector Los LED en el frente del lector LMSC1000 se iluminarán en rojo cuando enciendan. Los LED azules parpadeantes indican que se está leyendo una etiqueta de RFID. Salida de relé de contacto seco - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 20
Diagrama de cableado del lector Transformador eléctrico Negro Negro c/rayas Lector de RFID LMSC1000 Rojo Negro Verde Blanco Amarillo Los cables gris, azul y marrón del lector de RFID no se usan. Blanco Verde Negro Power +12 V RESET - 12 VCC ( - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 21
DC SETUP 6 LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Dry Cont Activar/desactivar la señal sonora De manera predeterminada, el LMSC1000 emitirá una señal sonora cuando lea una etiqueta de RFID. Para alternar esta función (encender o apagar) realice los siguientes pasos: 1. Coloque el - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 22
Programar sus etiquetas LiftMaster en myQ® Business™ Cuando agregue una credencial nueva en myQ® Business,™vaya a rese de que estén montadas correctamente y lejos de cualquier fuente de interferencia. Consulte el manual de instalación de las etiquetas de RFID y asegúrese de que las etiquetas estén - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 23
salidas Wiegand enviadas al controlador. Cambie la configuración del retraso de retransmisión Wiegand (de 0 a 15 segundos) siguiendo los pasos en el manual de instalación. Partes de repuesto Parte Ménsula de montaje Módulo de interfaz Wiegand Fuente de energía de RF - 3 amperios Número de pieza - LiftMaster LMSC1000 | Installation Manual - English French Spanish - Page 24
Garantía limitada de un año LiftMaster garantiza al primer comprador minorista de este producto, que el mismo está libre el distribuidor o con un técnico de radio/TV experimentado para pedir ayuda. 01-39457C © 2019, LiftMaster All Rights Reserved Tous droits réservés Todos los derechos reservados
Introduction
The LiftMaster proprietary Long Range Reader and vehicle tags provide you
quick and easy access into your gate. The LiftMaster reader and vehicle tags
must be used as a system in order to function. The LiftMaster branded tags
can only be used with the LiftMaster branded reader.
LIFTMASTER LONG RANGE RFID READER
Model LMSC1000
WARNING:
This product can expose you to chemicals including
lead, which are known to the State of California to cause
cancer or birth defects or other reproductive harm. For more
information go to
www.P65Warnings.ca.gov.
Carton Inventory
Supported LiftMaster RFID tags
(Order Separately)
LMSC1000 RFID Reader
LMHNTG/SPLMHNTG*
LiftMaster RFID Hang tag
*
If specific Facility Code and Start ID required, use special part #s SPLMHNTG,
SPLMUNTG.
** The SW2 is not intended to be used on anything other than the LMSC1000.
LMUNTG/SPLMUNTG*
LiftMaster Dual-Purpose RFID
Tag (Windshield/Headlamp)
Mounting Bracket
S2W Wiegand Interface
Module
12V 3A Regulated Power
Supply
The S2W Wiegand Interface Module
and plug-in transformer shall
be mounted in either the CAPXL
enclosure or a Gate Operator Listed to
UL 325, or a weather proof enclosure:
UL Listed NITW or CYIV, Types 3X,
3RX, 3SX, 4X OR 6P.
U-Bolts (2)
Reader Specifications
Part Number
LMSC1000
FCC ID
XVY-IDRO900MA
Dimensions
10.25" x 10.25" x 1.5"
Polarization
Circular Polarized
Frequency range
902Mhz ~ 928 MHz
Supported Protocol
ISO 18000-6C/EPC C1 G2, ISO 18000-6B
Read Range
20 – 30 Feet (Depending on Tag)
Anti-Collision
Up to 100 tags/second
Environment
Operating Temp : - 20 C to + 50 C
Storage Temp : - 20 C to + 80 C
Connectivity
26-Bit Wiegand (D0, D1, GND)
RF Output Power
Adjustable 13-30 dBm with 1 dB steps
Power Accuracy +/- 0.5dBm
Weight
< 31.0 oz. (Reader Only)
Protocol
ISO18000-6C C1G2
Firmware
v.EI8070400
LMSC1000 input rating
12V DC, 700 mA
UL 294 Levels
Attack: I, Line Security: I, Endurance: IV,
Standby: I
S2W_001 electrical
ratings**
Input rating: 12 Vdc, 20 mA
Relay output rating:
24 Vdc, 1 A
Compatible UL Listed
control Panels
Chamberlain Group, Models CAPXL and
CAP2D
Model S2W is intended
to be installed within a
weather proof
enclosure
UL Listed NITW or CYIV, Types 3X, 3RX, 3SX,
4X, or 6P
LMHNTG
FC: 24
ID: 00025
Remove permit while vehicle is in motion.
07/18
07/18
FC: 24
ID: 000025
FC: 24
ID: 000025
LMUNTG Windshield/Headlamp Tag
NOTE:
UL verified compatibility with CAPXL and CAP2D. S2W-001 module
must be energized from either the Triad Magnetics, Model WSU120-3000
or C.SA Electronics (Dongguan) Co., Ltd Model CS1203000.